WESTEK TM1627DOLB Manual De Instrucciones Y Garantía

OUTDOOR DIGITAL WEEKLY TIMER
Instruction Manual & Warranty
LCD Display Nomenclature:
Note: Not all functions are available on each timer.
1. AM/PM will appear when 12-hour is set
2. MO to SU stand for Monday, Tuesday, Wednesday,
Thursday, Friday, Saturday and Sunday
3. Hour:Minute:Second
4. R will appear when Random mode is enabled
5. Manual/Auto mode.
AUTO OFF, the device is in Timer Mode and remains off until
the first ON setting in programs
AUTO ON, the device is in Timer Mode and remains on until
the first OFF setting in programs
ON, timer remains on, and will not run any program until
override key is pressed and AUTO is displayed
OFF, timer remains off, and will not run any program until
override key is pressed and AUTO is displayed
6. CTD will appear when countdown is enabled.
7. DST will appear when day light saving enabled
8. D2D will appear when Dusk to Dawn enabled.
9. Program #, up to 20 programs are available
10. ON/OFF indicate the output status
Before using your timer for the first time, please
read the instructions carefully.
TM1627DOLB Features
20 programmable ON/OFF settings per week
•
12 hour AM/PM or 24 hour display
•
Programmable in 1 minute intervals
•
Daylight Saving Time setting
•
Random ON/OFF Feature (2~30 minutes of programmed time)
•
Dusk to Dawn
•
• Countdown
• Manual override – temporarily or permanently overrides
current program
Key Functions
• SET: Selects and confirms the program setting.
• DOWN/UP: Increase or decrease day and digit settings. Also
used to enable the Count Down function by pressing and
holding DOWN/UP together.
• ON/OFF: Allows user to select On, Off or Auto. Can be used for
manual override of timer settings without losing programming.
• D2D: Press D2D to enter D2D mode ,it will turn on at dusk and
turn off at dawn. ON/OFF will indicate the status of current
timer output
• RND: Press Random ON/OFF setting to activate random delay
for start or finish of ON periods.
• RESET: Use a pencil or paper clip to press the reset key to
initiate programming.
The timer clock must be set before programming any On/Off settings.
Setting the current time
1. If display does not appear, plug unit into a receptacle and
charge the internal battery for 1 hour.
2. Remove the unit from the receptacle and press the RESET key
to begin programming.
3. Press and hold the ON/OFF key, then press the DOWN key to
toggle between 12 or 24 hour display. AM will appear on the
display when 12 Hour display is selected.
4. Press and hold the ON/OFF key, then press the UP key to toggle
between normal and Daylight Savings Time. DST will appear on
the display, one hour ahead of the current time. Press the UP
key again to again to cancel DST.
5. Press and hold SET key for 3 seconds ,the "MO" flashes on
display, using DOWN or UP keys to select the current day, press
the SET key again to confirm your selection.
6. Hour digits flash on display, using DOWN or UP keys to select
current hour, press SET key again to confirm.
7. Minute digits flash on display, using DOWN or UP keys to select
current minute, press SET key again to confirm. There is no
option to set the Seconds.
Note: If programming is interrupted for more than 30 seconds while
setting the time, the unit will automatically revert to default mode.
Preset time will be preserved.
Programming priorities are
D2D> Manual ON/OFF>Random>CTD>Programmed events
Dusk to Dawn Function
• Press D2D to enter D2D mode ,it will turn on at dusk and turn off
at dawn. ON/OFF will indicate the status of current timer output
Manual Override
The ON/OFF key can be used to switch ON or OFF. Repeated
pressing of the ON/OFF key causes scrolling from AUTO
OFF(default)–MANUAL ON–AUTO ON–MANUAL OFF–AUTO OFF.
• AUTO OFF, the device is in Timer Mode and remains off until the
first ON setting in programs
• AUTO ON, the device is in Timer Mode and remains on until the
first OFF setting in programs
• ON, timer remains on , and will not run any program until
override key is pressed and AUTO is displayed
• OFF, timer remains off , and will not run any program until
override key is pressed and AUTO is displayed
Random Function
Turns On after 2-30 minutes of your programmed ON settings, turns
Off before 2-30 minutes of your programmed Off settings . To
activate Random Function, press RND button until "R" appear on
display. Press again to cancel. Setting the Random Function will
affect all 20 Programs.
Note: Programming of switching times (ON/OFF) will not work
properly if 'program ON' overlaps with 'program OFF'
Count Down On/Off Setting
1. Press UP or DOWN key for 3 seconds to enter "CTD" setting
interface
2. Press SET key ,OFF flashes on display ,use DOWN or UP keys to
select ON or OFF, press SET key to confirm.
• OFF option, keep timer on and turn timer off when CTD finished
• ON option, keep timer off and turn timer on when CTD finished.
R
3. Hour digits flash on display ,Use DOWN or UP keys select hour(s),
press SET key to confirm.
4. Minute digits flash on display, using DOWN or UP keys to select
minute, press SET key to confirm.
5. Seconds digits flash on display, using DOWN or UP keys to
select seconds, press SET key to confirm.
6. Press CTD key to start count down, press CTD key again to stop
count down. Timer will keep the status before CTD stopped.
Note 1: if you are at the current time display, press CTD key ,it will
start count down too , CTD on display will flash and ON/OFF will
indicate the status of current timer output
Note 2: If programming is interrupted for more than 30 seconds
while setting CTD, unit will automatically revert to default mode.
Preset time will be preserved.
Programming ON/OFF Events
Note: If a programming step is interrupted for more than 30
seconds, unit will automatically revert to default mode. Press Reset
to start the process over.
1. Clock time must be set before programming ON/OFF times.
2. After clock has been set, press the UP key.
3. Press the SET key to edit 1 ON program. Use the UP or DOWN
keys to cycle through the days of the week selections.
Options
1. Individual day of the week
2. MO TU WE TH FR SA SU (Every day)
3. MO TU WE TH FR (Weekdays only)
4. SA SU (Weekends only)
5. MO TU WE TH FR SA
6. MO WE FR
7. TU TH SA
8. MO TU WE
9. TH FR SA
10. MO WE FR SU
Press the SET key again to confirm your selection.
4. Next the Hour digits will flash on the display, use the DOWN or
UP keys to select the starting hour. Press the SET key again to
confirm your selection.
5. Next the Minute digits will flash on the display, use the DOWN or
UP keys to select the starting minute. Press the SET key again to
confirm your selection.
Next the program 1 OFF setting needs to be programmed.
6. Press UP key to enter 1 OFF editing.
7. Repeat steps 3 thru 5 to set day(s) and enter the day and time
the device should turn OFF.
8. To set additional ON/OFF cycles, (maximum 20 events), press
UP key. Then press UP or DOWN keys and follow procedures in
steps 3 thru 5 for each new ON/OFF event. When finished, press
UP or DOWN keys to exit , or wait for 1 minute (30 seconds to
exit interface of edit timing, 30 seconds to exit interface of
program event)
Note 1: Programming of switching times (ON/OFF) will not work
properly if 'program ON' overlaps with 'program OFF'
Note 2: If programming is interrupted for more than 30 seconds
while setting program, unit will automatically revert to default
mode. Preset time will be preserved.
Deleting Programs
1. Press UP key. Use UP or DOWN keys to select ON/OFF event to
be deleted.
2. Press ON/OFF key to delete program setting. Press again to
restore.
3. When done, press UP or DOWN keys to exit ,or wait for 1 minute
(30 seconds to exit interface of edit timing, 30 seconds to exit
interface of program event)
Reset key
Press RESET key. Timer will resume in default status. All time and
program information will be lost.
RATINGS:
125 Volts 60Hz
15A General Purpose
15A Resistive
8A, 1000W Tungsten
1/2 HP
One-Year Limited Warranty
AmerTac warrants to the original purchaser that this product will be free from defects in
materials and workmanship for a period of one year from the date of purchase. Additional
details are available at www.amertac.com. Prop. 65 Warning: This product contains
chemicals known to the State of California to cause cancer and/or birth defects or other
reproductive harm.
Garantie limitée de 1 an
AmerTac garantit à l'acheteur initial que, dans des conditions normales d'utilisation, ce
produit sera exempt de défaut de matériaux et de fabrication pendant une période de 1 an
à compter de la date d'achat. Des détails supplémentaires sont disponibles sur le site
www.amertac.com.
Garantía Limitada de 1 Año
AmerTac le garantiza al comprador original que este producto estará libre de defectos en
materiales y mano de obra por un período de 1 año a partir de la fecha de compra. Detalles
adicionales disponibles a través de www.amertac.com.
AmerTac
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China
© 2017 AmerTac™
I17-0008-A
TM1627DOLB
(maximum 20 events)
CONFORMS TO UL STD
60730-1, 60730-2-7
CERTIFIED TO CSA STD
E60730-1,E730-2-7
CUMPLE LA NORMA UL
60730-1, 60730-2-7
CERTIFICADO SEGÚN LA
NORMA CSA
3160817
E60730-1,E730-2-7
CONFORME À LA
NORME UL STD 60730-1,
60730-2-7
CERTIFIÉ
CONFORMÉMENT À LA
NORME CSA STD
E60730-1,E730-2-7