EnGenius ENS200 Guia De Inicio Rapido

Quick Start Guide
ENS200 | ENS202
Outdoor Client Bridge/Access Point
3
Bridge/AP Setup
A) To configure the Bridge/AP, open a web browser. In the address
bar of the web browser, enter 192.168.1.1 and hit enter.
B) A login screen will appear. By default, the username of the Bridge/AP
is admin and the password is admin. Enter the current username and
password of the Bridge/AP and then click Login.
Package Contents
Bridge/AP PoE Injector
Quick Start Guide
ENS200 | ENS202 | ENS500
version l.0
2.4 GHz, Long Range Wireless N300
Outdoor Access Point/Client Bridge Outdoor Client Bridge/Access Point
Quick Start Wall Mount
Guide Screw Set
Minimum Requirements
Broadband Internet Service
+
(Cable or DSL Modem)
| ENS500 Internet Browser
+
(Internet Explorer, Safari, Firefox, Chrome)
version l.0
4
Switching Modes
A) This device can operate in the following modes: Access Point,
Client Bridge, WDS AP, WDS Bridge, WDS Station and Client Router.
B) Click on the Operation Mode link under the System Properties.
1
Connecting the Bridge/AP
A) Remove the rear bottom panel.
B) Connect one end of the Ethernet cable into the LAN(PoE) port of the
Bridge/AP and the other end to the PoE Ethernet port on the PoE injector.
C) Connect the Power Adapter to the DC-IN port of the Bridge/AP and plug
the other end into an electrical outlet.
D) Connect the second Ethernet cable into the LAN port of the PoE injector
Power Adapter
and the other end to the Ethernet port on the computer.
E) Place the panel removed from step A back into the device.
Note: The Bridge/AP should ONLY be powered via Ethernet cable
connected to the included PoE Injector.
Pole Mounting
Strap x2
A
A
D
To Computer
5
Device Positioning
To optimize the point-to-point performance, adjust the devices so that they
are directionally facing each other.
Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary
depending on many factors including environmental conditions, distance between devices,
radio interference in the operating environment, and mix of devices in the network. Features
and specifications subject to change without notice. Trademarks and registered trademarks
are the property of their respective owners. For United States of America: Copyright © 2013
EnGenius Technologies, Inc. All rights reserved.
2
IP Address Configuration
A) Once your computer is on, ensure
that your TCP/IP is set to On or
Enabled. Open Network
Connections and then click Local
Area Connecton. Select Internet
Protocol Version 4 (TCP/IPv4).
B) If your Computer is already on a
network, ensure that you have
set it to a Static IP Address on
E
B
the interface.
(Example: 192.168.1.10 and
B the Subnet Mask address as
255.255.255.0.
C
C
Technical Support
Country of Purchase
North America
www.engeniuscanada.com
www.engeniustech.com
Central & South America
es.engeniustech.com
pg.engeniustech.com
Europe
www.engeniusnetworks.eu
Africa
CIS
Middle East
Russia
www.engenius-me.com
Asia
Oceania
www.engeniustech.com.sg
Others
www.engeniusnetworks.com
Service Center Service Information
Canada
rma@engeniuscanada.com
Toll Free: (+1) 888 397 2788
Local: (+1) 905 940 8181
Los Angeles, USA
support@engeniustech.com
Toll Free: (+1) 888 735 7888
Local: (+1) 714 432 8668
Miami, USA
miamisupport@engeniustech.com
Miami: (+1) 305 887 7378
Sao Paulo, Brazil: (+55) 11 3957 0303
D.F, Mexico: (+52) 55 1163 8894
Netherlands
support@engeniusnetworks.eu
(+31) 40 8200 887
Dubai, UAE
support@engenius-me.com
Toll Free:
U.A.E.: 800-EnGenius
800-364-364-87
General:
(+971) 4 357 5599
Singapore
www.engeniustech.com.sg/e_warranty_form
techsupport@engeniustech.com.sg
Toll Free:
Singapore: 1800 364 3648
Taiwan, R.O.C.
technology@senao.com