BaByliss PRO Nano Titanium MiraCurl BABNTMC1 Manual Del Usuario página 4

CURL DIRECTION SETTING (Right/Left/Alternate)
Use the curl direction control to choose either a uniform or natural finish. Select the curl
direction by sliding the switch to either left (l) or right (r) or alternate (a).
(l) starts the curl to to the left, counterclockwise.
(r) starts the curl to the right, clockwise.
you can also select the opposite direction on each side to create a symmetrical look.
When styling the left side of the hair, slide the curl direction switch to the left position (l).
When styling the right side of the hair, slide the switch to the right position (r). this ensures
that the curl sits toward the face on both sides of the head and will give a more uniform style.
For a more natural look, select the alternate setting (a). this will alternate the direction
after each curl.
INSTRUCTIONS FOR USE
• Ensure hair is dry and combed through.
• Plug the styler into a 120V outlet.
• Slide the temperature switch to the required heat setting.
• The styler is ready for use when the ON indicator light
has stopped flashing.
• There are 3 time settings; choose the optimum setting
for your hair type. alternatively, switch the time setting
to 0.
• Select the curl direction by sliding the control to either
position l, r or a.
• Separate a section of hair that is no wider than 1 inch
(Figure a). ensure that the section is clean, dry and
combed through.
• Please note the styler must be positioned into the hair
with the opening of the curl chamber facing toward
the head (Figure b).
• Position the styler where you want the curl to start.
the hair section must be straight, and placed neatly
through the center of the styler (Figures c and d).
• Once the hair is in place, let go of the hair section and
close the handle to allow the hair to be automatically
taken into the curl chamber (Figure e).
BABNTMC1 IB-12152B.indd 7-8
NOTE: if you continue to hold the hair section after closing the handle the miracurl
stop and beep to indicate that you must release the tension on the hair. if you have taken
too much hair, or hair is not neatly going through the center of the appliance, the miracurl
will again stop and beep to indicate a problem. this safety feature ensures there will be
no tangles.
• The hair is automatically drawn into the ceramic curl chamber where it is softly held and
heated from all directions to effortlessly form the curl.
• If you are using the timer setting, the automatic beep indicator will start as soon as the
handles are closed together. there will be a series of individual beeps. hold the styler
still, with the handles held together until the end of the individual beeps. there will then
be four quick beeps in succession. this indicates that the time is up and you can remove
the styler from the hair. NOTE: When the audio off 0 setting is selected, there will be no
beep indicator. there will just be a warning beep at 15 seconds.
• It is very important that you release the handles fully, and then gently
pull the styler away from the head to free the hair and reveal the curl
(Figure F).
NOTE:
Always release the handles first to set the curl free; if you pull away before you
open the handles, the curl will be straightened out.
• To allow the curl to set, do not comb or brush the hair until it cools.
• Repeat around the head until you have the amount of curls desired.
A
SMART TECh
miracurl
• Auto Shut Off: if the appliance is switched on for more than 60 minutes continuously,
it will automatically switch off. if you wish to continue using the appliance, simply slide
B
the switch to off position and then slide the switch to the relevant setting to turn the
power on.
• Sleep Mode: After 20 minutes of idle time, the temperature drops to around 300°F/150°C.
• Motion Sensor: move the iron and close it to trigger the reheat to set temperature.
C D
E
®
comes with 3 functions for added safety and energy savings.
®
will
®
®
F
2/17/14 5:10 PM