JB Systems SMOOTH SCAN-BLUE LASER Manual De Instrucciones página 6

ENGLISH
4) IR remote MODE:
The laser can be controlled by the IR remote control:
 Press the FUNC-button until the display shows: "REM".
 Press the ENTER-button to confirm your choice.
Note: In any standalone mode (excepted REM and SLA), press ON/OFF for 2 second to activate remote
function.
AUTO SHOW
MUSIC SHOW
LASER ON/OFF
COLOR
EFFECT PAUSE
CHANGING PATTERN
SOUND SENSIVITY
FIXED PATTERN (FROM 1 TO 48)
PATTERN REPEATING
Remote control details:
Button function
In REM mode, turn on/off the laser. In any oder
ON/OFF
standalone mode except SLAVE, press 2s to turn on the
AUTO
Sound activated show, the blue is flashing when the
MUSIC
In sound activated mode, press music+B+1to 9 to change
Sound sensivity
COLOR
To change the color from red to green or red & green
CHANGING
PATTERN
CHANGING
FIXED
PATTERN
PATTERN
Last pattern and current pattern cycle repeating
REPEAT
5) DMX512 MODE:
The laser can be controlled by any standard DMX-controller in 2 different DMX-modes:
 1 CHANNEL MODE: for extremely easy setup and use! (display shows "1Ch")
 17 CHANNEL MODE: for full control on every functionalities. (display shows "17c")
 Connect the DMX input of the laser to the DMX output of the previous unit in the chain or directly to the
DMX-output of your controller.
 Press the FUNC-button until the display shows: "1Ch" or "17h".
JB SYSTEMS
®
USER MANUAL
Description
REM mode
Auto running show
sound is detected.
the sensivity settings
To show and change patterns
You can select one pattern from 1 to 48
7/62 SMOOTH SCAN-BLUE LASER
ENGLISH
 Press the UP/DOWN buttons to select the DMX-mode. (1ch or 17ch)
 Press the ENTER-button to confirm your choice.
 Press the FUNC-button: the 3 digit number on the display starts blinking.
 Select the DMX-address
 Press the ENTER-button to confirm your choice.
Note: the display blinks when the unit is in DMX-mode and no DMX-signal is detected.
Some more information on DMX512:
The DMX-protocol is a widely used high speed signal to control intelligent light
equipment. You need to "daisy chain" your DMX controller and all the connected light
effects with a good quality XLR M/F balanced cable. To prevent strange behavior of the
light effects, due to interferences, you must use a 90Ω to 120Ω terminator at the end of
the chain. Never use Y-splitter cables, this simply won't work!
Each effect in the chain needs to have its proper starting address so it knows which commands from the
controller it has to decode.
1 CHANNEL DMX-CONFIGURATION OF THE LASER:
DMX-
position value function
4 210-255 SOU
3 150-209 AUT
2 090-149 SOP
1 030-089 AUP
0 000-029 STANDBY
17 CHANNEL DMX-CONFIGURATION OF THE LASER:
IMPORTANT REMARK: DMX Channel1 is used to set the different working modes of the laser.
 To use the laser in full 17 channel mode, channel 1 must be set to value 221 or higher.
 Depending on the DMX-values of channel1, different mode can be applied:
DMX-
Channel value
000-040
041-080
081-120
CH1
Mode
121-160
161-200
201-255
000-051
052-103
CH2
104-155
Group
156-207
208-255
CH3 Pattern 000-255
JB SYSTEMS
®
USER MANUAL
remarks
Sound activated show
Automatic show
Sound activated pattern effect show
Auto running pattern effect show
Laser output off
function
Laser OFF
AUT
SOU
AUP
SOP
DMX MODE
1 Group Patterns.
2 Group Patterns
3 Group Patterns
4 Group Patterns
5 Group Patterns
Every 16 for 1 group, total 80 patterns.
8/62 SMOOTH SCAN-BLUE LASER