Ecco REFLEX 5500 Serie Instrucciones De Instalacion Y Uso página 2

Caution: When drilling into any vehicle surface, make sure the area
is free from any electrical wires, fuel lines, vehicle upholstery, etc. that
could be damaged
Permanent Mounting:
1. Select the desired location on a flat surface for the
Minibar to be mounted. The visibility of the flash and
ease of wiring access should be taken into
consideration in the selection of the mounting location.
2. Remove lens screws, then remove lens. Use the four holes in the
corners of the base to mark the mounting hole locations.
3. Drill the holes using a 7/32" drill size.
4. A fifth hole may be drilled for wire access.
5. Connect the power wires as shown in the wiring section
(see Figure 6).
6. Mount the minibar with M5 hardware provided.
!
WARNING!
Failure to follow these instructions can result in fire or injury from excessive heat build up.
Operator is responsible for ensuring auxiliary plug fits correctly into auxiliary power plug outlet used.
For proper operation, verify auxiliary power outlet circuit is rated to supply a minimum of 10 amps. (See specifications section for rated current in amperes).
Do not exceed the current rating for the auxiliary power outlet recommended by vehicle manufacturer.
Keep auxiliary plug and outlet clean and free of debris.
Do not use the auxiliary plug when wet.
Insert auxiliary plug fully into the outlet for proper connection.
Grasp auxiliary plug, NOT cord, to remove from outlet.
Remove auxiliary plug completely from outlet when light is not in use.
Important! Disable power before wiring up the Minibar.
Vacuum Mount Installation for 5500 Series:
1. Remove round black stickers for vacuum placement
2. Remove lens screws, then remove lens.
3. Unclip and remove wire harness
4. Position vacuum magnets, place, and tighten screws.
5. Insert pinned end of cable through the wire harness hole from the
bottom of the base. Pull at least 6 inches of slack.
6. Turn pins crimp side up, and insert pins into connector as shown in
Figure 3.
7. Place zip-tie 1.0" from base of the connectors shown in Figure 4.
Zip-tie must not slide on cord.
8. Trim excess zip-tie.
9. Clip connector to the PCA board and pull slack until zip-tie touches
base.
10. Install lens, reverse of removal.
11. Slide o-ring onto screw until it reaches head, before placing into lens.
If o-rings are damaged, replace with new ones.
920-0149-00 Rev. K
Figure 2
!
WARNING!
Maximum recommended vehicle speed for safe operation using the
Vacuum Mount model is 65 mph (104 km/h), when fitted to the center of a
vehicle roof of steel construction. Higher speeds could cause the mount
to fail, resulting in the minibar flying off of the vehicle, which could cause
damage to other vehicles, and injury or death to the passengers. The
vacuum-magnet mount is not intended as a permanent mounting for the
minibar. The vacuum-magnet mount unit must be mounted on a flat smooth
magnetic surface (i.e. no fiberglass, ribbed style roofs, etc.). Ensure that
the magnet is kept clean.
PULL/ROLL TAB UPWARD TO RELEASE VACUUM
Note: Operating the Minibar without the lens installed on this product will
result in damage that will not be covered under warranty.
BLACK WIRE
PIN 1
Magnet Mount Installation for 5500 Series:
1. Refer to the appropriate Vacuum Mount Installation for the 5500 series,
steps 2 through 9, and the corresponding Figures for wiring instructions for
the cord.
2. Place hex nut into the hex shaped retaining cavity on the inside of the mini-
bar base.
3. Place an internal star washer onto the enclosed M5 x 20 hex bolt and insert
the hex bolt through the hole in the cup magnet as shown. Hold the magnet/
bolt assembly with the bolt extended through the magnet as far as possible
and feed the hex nut and the shank of the bolt through one of the openings
at the 4 corners of the underside of the minibar base. Maintain tension on
the bolt/nut by holding onto the cup magnet while tightening the assembly.
Repeat this process for all four corners. See Figure 5.
4. Place the adhesive magnet covers over the magnets.
5. Replace the lens.
NOTE: Operating the vehicle without the outer lens installed on
the product may result in damage that will NOT be covered under
warranty.
PULL/ROLL TAB
UPWARD TO
RELEASE VACUUM
Figure 1
GREEN WIRE
PIN 3
RED WIRE
PIN 2
Figure 3
Page 2 of 12