Fagor SCT 8000 Manual Del Usuario página 11

2. DVB-C OUTPUT: DVB-C output
2.1. QAM Mode:
16QAM, 32QAM, 64QAM, 128QAM,
256QAM.
2.2. IQ mode:
normal, Inverted.
2.3. Roll Off: 13, 15.
2.4. Baud Rate (KB): 1000 ÷ 6960.
3. SAT INPUT: Satellite input signal
3.1. DVB Mode:
DVB-S, DVB-S2.
3.2. In Frequency:
FI SAT 950 ÷ 2150 MHz.
3.3. Baud Rate:
4.000 ÷ 45.000 KB, DVB S
10.000 ÷ 30.000 KB, DVB S2.
3.4. Roll Off:
20, 25 y 35%, DVB S2 only.
3.5. Init Tuner:
Syncronize the tuner (press
3.6. Auto Mode:
Sets the type of modulation and DVB-C
Baud rate to match the bit rate of input with the
output:
1.- If the input bit rate ≤ bit rate maximum of 64 QAM,
the appropiate baudrate for 64 QAM is set.
2.- If "1.-" is not met, 256 QAM and 6960 Kbaud is
set (máximun output bit rate).
3.7. * Modulation:
indicates the modulation type.
3.8. * BER:
indicates the value of BER.
3.9. * S/N:
indicates the input S/N
(Recommended S / N > 11 dB).
* This data is shown when the tuner is tuned.
4. OUTPUT SERVICES
- This function is only visible when the tuner is tuned.
4.1. List of Services:
list of services.
Press to view the list.
●
❏ ❏
Press to select the service.
▲
▼
●
Press to enter the service parameters.
●
– A "+" sign followed by the name of the service indicates
that this service is in the output multiplex.
– A " * " sign before the name indicates an encrypted
service.
4.1.1. Active:
enables the service on output MUX
❏ ❏
(use to select and press
▲
▼
4.1.2. LCN:
Allows assigning a LCN (Logical Channel
Number) between 1 and 1023 to the services at the
❏ ❏
output (select with
▲ ▼
stands for NO LCN).
- To change the LCN is necessary having the NIT Mode
in "Local" option. See 5.1.
4.1.3. Program Number:
indicates the service PN.
4.2. Output MUX BW:
indicates the total % of the output
MUX occupied.
).
OK
.
).
OK
and press ; 0000
OK
- It is not recommendable to work with the output MUX BW
above 80%, as the services may increase their bitrate during
transmission. (Output MUX BW > 92%: Status LED in yellow).
4.3. Clear all:
clears all the services selected in the DVB-T
output. "Press ".
OK
4.4. Active all:
Enable all services present in the input.
- With encrypted services there is the risk of overload
the processing capacity of the CAM.
4.5. Read Services:
reads the transponder services.
"Press ".
OK
5. PSI EDIT:
Allows the Output's NIT configuration.
5.1. NIT Mode:
Pass-Through / LOCAL selection. If local is
chosen, allows modifying the following parameters.
5.2. Network Name:
Allows living a name to the network.
5.3. Network ID:
(give the same value as the Orig.Net.ID).
5.4. TS ID:
Some receivers need a different TS ID for every
memorised module (value between 0 and 65535).
5-5 Orig. Net. ID:
Original Network Identifier by Country
(see table 3).
5.6. Vr. NIT:
NIT version table( SCT-CI 8000).
5.7. Vr. SDT:
SDT version table( SCT-CI 8000).
6. CAM: access to MMI and CAM menus
(SCT-CI 8000)
6.1. Read MMI:
Open the session with the MMI
(only option available if session is not open).
If the session is open, the last option is read again.
6.2. Close MMI:
Closes the session with the MMI.
It's recommended to close the MMI session once
finished the access.
6.3. MMI menu:
Options list or CAM information.
It can appear a first information line followed by the list
of options with a number. The last option (0.Quit) goes
to the precedent menu. If the information to show
is longer than the display size, push
of the text.
6.4. MMI Enquiry:
CAM's data introduction (example
insert PIN). Look at point 6.5.
6.5. Enter User Input:
CAM's data introduction.
7. MEMORY
- Automatic save: 30 minutes after the last button is
pressed, the current data will be stored in the STT
8000.
11
to read the rest