Toshiba RAS-10N3KVP Manual De Instrucciones página 4

INDOOR UNIT DISPLAY
1
1 2 3 4
PREPARATION BEFORE USE
2
Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type) following
the (+) and (–) positions.
Clock Setup
1. Push by tip of the pencil.
2. Press : adjust the time.
3. Press : Set the time.
Remote Control Reset
Press for reset.
AIRFLOW DIRECTION
3
Press : Move the louver in the
1
desired vertical direction.
Press : Swing the air automatically
2
and press again to stop.
3
For horizontal direction, adjust manually.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
REMOTE CONTROL
4
1
Infrared signal emitter
2
Memory and preset button (PRESET)
3
Start/Stop button
4
Temperature up/down and
Timer or clock up/down button (TEMP.)
5
Mode select button (MODE)
6
Swing louver button (SWING)
7
Fan speed button (FAN)
8
One Touch button (ONE-TOUCH)
9
Set louver button (FIX)
-
=
Economy button (ECO)
q
High power button (Hi-POWER)
w
Plasma Air Purifi er button (PURE)
e
Comfort sleep button (COMFORT SLEEP)
r
t
On timer button (ON)
y
Off timer button (OFF)
u
Setup button (SET)
i
Clear button (CLR)
o
Clock setup button (CLOCK)
p
Check button (CHECK)
[
Filter reset button (FILTER)
]
Reset button (RESET)
For 1:1 installation, there is an optional remote controller containing two more
exclusive features. The exclusive features are 8 degree celsius operation
(8°C button) and power selection (POWER-SEL button). Availble on the
optional remote controller, these two exclusive features are placed at location
- r
of and .
Please contact your distributor or retailer for further information on these extra
features and in order to purchase any optional remote controller. Its service
part number is 43T66311 (Model:WH-TA01JE).
5
1
Hi POWER (Green)
2
FILTER (Orange)
3
PURE (Blue)
4
TIMER (Yellow)
5
OPERATION (Green)
6
RESET button
6
1
2
3
5
8
-
w
t
y
o
p
ONE-TOUCH
5
Press the "ONE-TOUCH" button for fully automated operation that is
customised to the typical consumer preferences in your region of the world.
The customised settings control temperature air fl ow strength, air fl ow
direction and other settings to provide you alternate contact with "ONE-
TOUCH" of the button. If you prefer other settings you can select from the
many other operating functions of your Toshiba unit.
Press : Start the operation.
AUTOMATIC OPERATION
6
To automatically select cooling, heating, or fan only operation
1. Press : Select A.
2. Press : Set the desired temperature.
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
COOLING / HEATING / FAN ONLY OPERATION
7
1. Press : Select Cool
(Fan only operation is required optional remote controller)
2. Press : Set the desired temperature.
Cooling: Min. 17°C, Heating: Max. 30°C, Fan Only: No temperature
indication
3. Press : Select AUTO, LOW , LOW+
MED+ , HIGH
Note: QUIET is supper low fan speed for quiet operation.
When using a multi-system outdoor unit is connected, FAN ONLY
operation cannot be used.
DRY OPERATION (COOLING ONLY)
8
For dehumidifi cation, a moderate cooling performance is controlled
automatically.
1. Press : Select Dry
2. Press : Set the desired temperature.
AIR PURIFYING OPERATION
9
During air conditioner operation
Press to start and stop plasma air purifi er and air ionizer
operation.
The plasma air purifi er and air ionizer can be activated or deactivated during
air conditioner is stopped and the air ionizer starts in conjunction with plasma
air purifi er operation.
Note: The FILTER indicator (orange) turns on after PURE operation is
performed for about 1000 hours.
Hi-POWER OPERATION
10
To automatically control room temperature and airfl ow for faster cooling or
heating operation (except in DRY and FAN ONLY mode)
Press : Start and stop the operation.
4
6
7
9 ECO OPERATION
11
=
q
To automatically control room to save energy (except in DRY and FAN ONLY
e
r mode)
i
Press : Start and stop the operation.
u
]
Note: Cooling operation; the set temperature will increase automatically 1
[
degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation the set temperature will decrease.
TEMPORARY OPERATION
12
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or stop
without using the remote control.
• Operation mode is set on AUTOMATIC operation,
preset temperature is 25°C and fan operation is
automatic speed.
, MED
, or Quiet .
, Heat , or Fan only .
, MED
, or Quiet .
.
,
,