Publicidad
Idiomas disponibles
Idiomas disponibles
Scope of delivery (
Page
3)
Textile bag to store the car cleaning set
Ø 35 mm to Ø 32 mm adapter piece,
so that you can also use the supplied nozzles
(Ø 35 mm) for Ø 32 mm suction tubes
long, exible crevice nozzle for vacuuming
hard-to-reach places
Felt attachment for the exible, long crevice
nozzle to protect surfaces
Brush attachment for the exible, long crevice
nozzle for particularly delicate surfaces
Safety notices
Comply with the detailed operating
manual of the vacuum cleaner used.
Do not use the mini turbo brush on persons,
animals or plants. When cleaning ensure
that body parts cannot be vacuumed at any
time.
In addition, do not vacuum above cables,
lines, etc. as the rotating brush roller could
damage them. There is also a risk of them
getting tangled in the brush.
About the adapter piece
Suction tubes (
) are predominantly made
with a 32-mm or 35-mm diameter.
So that you can use the nozzles in either
case, 2 adapter pieces (
) are supplied for
suction tubes of 32 mm diameter.
Do you have questions?
If you have a question, problem or you want
to order accessories and spare parts, see
contact data
page
21.
6
GB
GB
Mini turbo brush for thorough brush vacuum-
ing, is particularly suited to cleaning up animal
hair amongst other uses
Flat nozzle to vacuum large areas of e.g.
upholstery
Micro- bre gloves (1 pair, 80% polyester, 20%
polyamide) with rough and ne sides to wipe
off dust from the interior of the vehicle
Suction tube of your vacuum cleaner (not
included in the car cleaning set)
Before you put the mini turbo brush onto
the suction tube or take it off, switch off the
vacuum cleaner.
Do not insert any objects into the openings
of the device or its accessories other than
those described here.
Store components of the car cleaning set
out of the reach of children.
Do not use the micro- bre gloves (
) to
clean the outside of the vehicle. This could
damage the paintwork.
About the crevice nozzle
When you use the long, exible crevice noz-
zle, under certain circumstances the pres-
sure inside the vacuum cleaner might drop
too far thus triggering the safety valve.
The signal for this is e.g. a whistling
noise (depending on the vacuum cleaner
model) and greatly reduced suction
performance.
In this case, depending on the vacuum
cleaner model and equipment, you have
to reduce the suction power or open the
bypass vent until the valve no longer
triggers.
Attaching the nozzle/brush
1. Try safely attaching the selected nozzle/brush
(
,
,
) to the suction tube
) without us-
ing the adapter piece (
).
– If it ts, twist the nozzle/brush slightly when
pushing it on to secure it.
– If it doesn't t, you require an adapter piece
(
) to adjust the diameter of the nozzle/
brush to that of the suction tube. Push the
adapter piece with the rounded edge to-
wards the opening. Now attach the nozzle/
brush. Twist the nozzle/brush slightly when
pushing it on to secure it.
Cleaning the mini turbo brush
To clean the mini turbo brush thoroughly (
dismantle it as follows:
1. Switch off the vacuum cleaner.
2. Pull the brush off the suction tube.
d
LOCK
c
a
UNLOCK
Looking after the micro- bre gloves
When washing the micro- bre gloves (
)
make sure you observe the following:
Wash the micro- bre gloves by hand or
at no more than 60 °C.
Use a mild washing liquid without
softener.
Do not bleach the micro- bre gloves,
iron them or dry them in a dryer.
Instead, leave the micro- bre gloves to
dry for 24 hours at room temperature.
2. If you use the long, exible crevice nozzle
(
), attach either the felt attachment (
the brush attachment (
) to it.
This is the best way to protect the surfaces
you are vacuuming. (When using the exible,
long crevice nozzle, also follow the instruc-
tions in the box "About the crevice nozzle"
Page
6)
3. Store accessories you don't need in the textile
bag (
).
3. Release the retaining nut by turning in the
),
"Unlock" direction (a).
4. Remove the top section of the housing (b).
5. Now thoroughly clean the brush by hand.
6. After cleaning, rst put the top section of the
housing into the three catches at the front
b
of the bottom section and then shut it at the
back (c).
7. Then tighten the retaining nut by turning in
the "LOCK" direction (d).
Accessories and Spare Parts
Article no./Fig.
Description/Content
0277001
1 exible, long crevice
nozzle & 2 attachments
0277002
1 at nozzle
0277003
1 pair of micro- bre gloves
0230001
1 adapter piece
M219
1 mini turbo brush
) or
GB
GB
7
Publicidad
