Campbell Hausfeld WG3000 Manual De Instrucciones Y Lista De Repuestos página 10

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

For Information About This Product, Call 1-800-746-5641
Symptom
No output
Wire tangles at drive roller
Gun nozzle arcs to work
surface
Work clamp and/or cable
gets hot
Wire does not feed
(Aluminum) Wire burns back
into tip or (Aluminum) Metal
bubbles or burns through
Symptom
Bead is intermittently too
thin
Bead is intermittently too
thick
Ragged depressions at
edge of weld
Weld bead does not
penetrate base metal
Wire sputters and sticks
www.campbellhausfeld.com
Troubleshooting Chart - Welder
Possible Cause(s)
1. Duty cycle exceeded
2. Poor work clamp connection
3. Defective power switch
4. Blown breaker or fuse
1. Wrong size gun tip
2. Gun liner clogged or
damaged
3. Gun tip clogged or damaged
4. Feed roller worn
5. Not enough tension
Slag inside gun nozzle
1. Poor contact
2. Using an extension cord with
excessive length
1. Wire jammed
2. Out of wire
3. Not enough tension
4. Wire liner worn
5. Fuse blown
6. Wire disconnected internally
7. Contact tip clogged
1. Wire speed too slow
2. Travel speed too slow or heat
is too high
Troubleshooting Chart - Welds
Possible Cause(s)
1. Inconsistent travel speed
2. Output heat setting too low
1. Slow and/or inconsistent travel
speed
2. Output heat setting too high
1. Travel speed too fast
2. Wire speed too fast
3. Output heat setting too high
1. Inconsistent travel speed
2. Output heat setting too low
3. No or low shielding gas
4. Wrong shielding gas (aluminum)
5. Extension cord is too long
6. (Aluminum) Possible oxide buid-
up on surface
1. Damp wire
2. Wire speed too fast
3. Wrong type of wire
4. No or low shielding gas
Corrective Action
1. Allow welder to cool until ON/OFF Switch lamp goes out
2. Be sure all connections are secure, and attaching surface is
clean
3. Replace switch
4. Reduce circuit load, reset breaker or replace fuse
1. Use proper size gun tip
2. Clean or replace gun liner
3. Clean or replace gun tip
4. Replace
5. Tighten tensioning screw
Clean slag from gun nozzle
1. Be sure all connections are secure, and attaching surface is
clean
2. Never use an extension cord longer than 20 ft
1. Reload wire
2. Replace wire spool
3. Tighten tensioning screws if wire is slipping
4. Replace liner
5. Replace fuse on wire feed control board inside welder,
(1.6 amp time delay)
6. Call 1-800-746-5641 for assistance
7. Replace contact tip
1. Run speed in 7 - 10 range
2. Increase the travel speed or reduce heat settings
Corrective Action
1. Decrease and maintain constant travel speed
2. Increase output heat setting
1. Increase and maintain travel speed
2. Reduce output heat setting
1. Decrease travel speed
2. Decrease wire speed
3. Reduce output heat setting
1. Decrease and maintain constant travel speed
2. Increase output heat setting
3. Use gas for MIG process or refill bottle
4. Use only 100% Argon gas
5. Never use an extension cord longer than 20 ft
6. Clean surface thoroughly with a stainless steel brush only
1. Use dry wire and store in dry location
2. Reduce wire speed
3. Use flux core wire when not using gas
4. Use gas for MIG process or refill bottle
10

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Wg3060

Tabla de contenido