Hudson Industro 91003CCV Instrucciones

FOR YOUR SAFETY
this sprayer operates with liquid under pressure. Failure
to observe cautions and follow instructions for use
and maintenance can cause tank, hose or other parts
to become corroded, weakened, and/or burst. This
can result in serious injury or property damage from
forcible ejection of parts or high-pressure discharge
of spray material. Do not use any flammables or
boiling liquids in this sprayer as it is not designed nor
intended for such use. Some spray materials can ignite
or explode. Do not spray in an enclosed space, near
an open flame such as found in a bbq grill or water
heater, near an electric motor or open switch, or any
source of heat. Do not smoke while spraying. Use of
flammables could result in serious injury or property
damage from unintended ignition or explosion. Do not
use any caustics or acids in this sprayer, since these can
damage or weaken the sprayer and its parts, resulting
in serious injury or property damage. Keep out of
reach from children and pets. Always read and follow
directions on the spray material container, including the
need for protective clothing. Before using your sprayer,
thoroughly inspect both inside and outside of the
sprayer and do not pressurize sprayer if tank, hose or
other parts appear to be damaged, discolored, brittle,
excessively soft or loose. Do not pressurize with any
mechanical device such as an air compressor, since this
can create dangerous pressure and bursting of parts
and result in serious injury. Wear long-sleeved shirt,
pants, gloves, goggles or similar protective clothing
when spraying. Prop 65 warning: handling the brass
material on this product exposes you to lead, a chemical
known to the state of california to cause birth defects or
other reproductive harm. Wash hands after use.
LIMITED WARRANTY
H. D. Hudson Manufacturing Company warrants to
the original consumer purchaser of this product at
retail that it is free from problems in materials and
workmanship for the period of 1 year from the original
date of purchase. This warranty does not apply to
damage to the product resulting from accident,
misuse, neglect, alteration, modification, tampering, or
failure to follow instructions supplied with the product.
This warranty does not cover normal wear and tear
of o-rings or seals, and the warranty shall be void if
the product is used commercially. If the product or
any part of it should malfunction within the warranty
period, call 1-800-977-7293. Valid only in North
America. You must retain your sales receipt as proof of
the date of purchase and include it with any return of
the product.
H. D. HUDSON MANUFACTURING COMPANY
EXCLUDES LIABLITY UNDER THIS WARRANTY FOR
ANY AND ALL INCIDENTAL AND CONSEQUENTIAL
LOSS OR DAMAGES.
871-048 Instruction
91003CCV, 91004CCV, 91703, 91704, 91704CCV
Industro® Steel Sprayer Instructions
If you have any questions or concerns, or missing parts, Do not return sprayer to the store!
Call our hotline: 1-800-9-SPRAYER (1-800-977-7293)
Common maintenance questions: www.hdhudson.com/FAQS
INSIDE THE BOX
(Parts may be loose in tank)
• Sprayer Tank with Supply Tube • Clamp
• Hose with Fitting and Nut • Nozzle Tip
• Pump in Tank • Instructions
• Shut-off Valve
View Online
Poly Tank Assembly Video @ hdhudson.com
HOW TO ASSEMBLE
Assemble Hose
1.
Hose to tank: Slide gear clamp onto hose.
Insert hose over barb attached to tank. Locate gear
clamp over barb & tighten clamp. Do not use any
kind of lubricant on the hose or fitting.
CAUTION! Failure to do so, can result in serious
injury from forcible ejection parts or high
pressure ejection of spray material.
2. Attach spray wand to shut-off valve.
• Insert spray wand fitting into shut-off valve.
• Screw down wand retainer cap nut onto valve.
Screw nut onto the shut-off valve. Note: This is not a
compression fitting, but it is normal for nut to screw
on tightly.
1.
.
2
View Online
See maintenance and instructional videos on the internet:
www.hdhudson.com/instructional-videos
HOW TO FILL
A.) Pour measured amount of spray material into
the open tank. Follow label directions on spray
material container for amount to use.
B.) Add water as directed. Do not fill beyond the
MAX FILL line.
C.) Hold cover upright, insert into tank.
D.) Lift and seat in tank opening. Turn handle across
width of opening.
A. B.
C. D.
HOW TO PRESSURIZE
Unlock pump handle by pushing down and turning
handle. Do not unscrew pump cap or remove
pump. Using the handle, pump up and down. The
more you pump, the more pressure you will build
up inside the tank. When it becomes difficult to
pump, your tank has reached maximum pressure.
Do not stand so your head is over pump.
• Use low pressure (fewer strokes) for a coarse spray.
• Use high pressure (more strokes) for a fine mist or
a long-reaching stream.
©2015 Manufactured by H. D. Hudson Manufacturing Company
HOW TO SPRAY
Squeeze handle to spray
Release handle to stop
HOW TO RELEASE PRESSURE
Turn sprayer on its side and turn nozzle away from
you. Squeeze lever or push button to "ON" and let all
the air escape. Turn Handle on cover either right or
left so it depresses air release valve pin. This opens air
release valve on cover to reduce tank pressure.
Do not stand so your head is over pump.
SERVICE AND MAINTENANCE
Visit www.hdhudson.com/FAQS
Clean and dry your sprayer after every use to greatly
prolong its useful service life. Many spray materials
will harden if left in the sprayer and plug up the
nozzle, shut-off valve or supply tube. The soft parts,
O-rings and gaskets, will ultimately wear out and
need replacing, just like the oil filter on your car, for
example. How often they need replacing depends
on how much you spray, the spray materials you
use and whether or not the sprayer is regularly
cleaned after use. Call 1-800-9-SPRAYER or visit
www.hdhudson.com to obtain genuine Hudson®
replacement parts. If you leave your sprayer in the
garage over Winter, particularly in northern areas,
the soft parts may dry out and need servicing
before you use your sprayer for the first time
in the Spring.