Stanley SRR1200 Manual De Instrucciones página 18

ENGLISH (
Original Instructions)
g. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazardous
situation.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
ADDITIONAL SAFETY INSTRUCTIONS
FOR ROUTERS
♦ Hold power tool by insulated gripping surfaces,
because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts of
the power tool "live" and shock the operator.
♦ Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
♦ Only use router bits with a shank diameter equal to the
size of the collet installed in the tool.
♦ Only use router bits suitable for the no-load speed of
the tool.
♦ Never use router bits with a diameter exceeding the
maximum diameter specified in the technical data
section.
♦ Do not use the tool in an inverted position.
♦ Do not attempt to use the tool in a stationary mode.
♦ Take special care when routing MDF or surfaces coated
with lead-based paint.
♦ Wear a dust mask specifically designed for protection
against lead paint dust and fumes and ensure that
persons within or entering the work area are also
protected.
♦ Do not let children or pregnant women enter the work
area.
♦ Do not eat, drink or smoke in the work area.
♦ Dispose of dust particles and any other debris safely.
♦ Always wear a dust mask.
♦ This appliance is not intended for use by young or infirm
persons without supervision. children must be supervised
to ensure they do not play with the appliance.
PERSONAL SAFETY
♦ No children or pregnant women should enter the work
rea where the paint sanding is being done until all
cleanup is completed.
♦ A dust mask or respirator should be worn by all persons
entering the work area. The filter should be replaced
daily or whenever the wearer has difficulty breathing.
Note: only those dust masks suitable for working with lead
paint dust and fumes should be used. Ordinary painting
masks do not offer this protection. See your local hardware
dealer for the NIOSH approved proper mask.
18
LABELS ON TOOL
The label on your tool may include the following symbols:
WARNING! To reduce the risk of injury, the user
must read the instruction manual before use.
Wear ear protection.
Wear safety glasses or goggles.
V Volts
A Amperes
Hz Hertz
W Watts
min minutes
Alternating
Current
Position of Date Code (Fig. A)
The Date Code, which also includes the year of manufacture,
is printed into the housing.
Example:
2016 XX JN
Year of manufacturing
PACKAGE CONTENTS
The package contains:
1 Router
1 Instruction Manual
♦ Check for damage to the tool, parts or accessories
which may have occurred during transport.
♦ Take the time to thoroughly read and understand this
manual prior to operation.
ELECTRICAL SAFETY
Your tool is double insulated; therefore no earth wire
is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
WARNING! If the power cord is damaged, it must be
replaced by the manufacturer, authorized Stanley
Service Center or an equally qualified person in order
to avoid damage or injury. If the power cord is replaced
by an equally qualified person, but not authorized by
Stanley, the warranty will not be valid.
USING AN EXTENSION CABLE
If it is necessary to use an extension cable, please used
an approved extension cable that fits the tool's power input
specifications. The minimum cross-sectional area of the
conducting wire is 1.5 sq. mm. Cables should be untangled
before reeling up.
Direct Current
n No-Load Speed
0
Class II Construction
Earthing Terminal
Safety Alert Symbol
Revolutions or
/min. Reciprocation per
minute