Draw-Tite Hide-A-Goose 9467 Instrucciones De Instalación página 2

This hitch meets all requirements of:
SAE J2638
Society of Automotive Engineers Standard for
Fifth Wheel and Gooseneck attachment performance
HITCH INSTALLATION:
1. Drop (3) rear exhaust hangers for easier access to tighten bolts. Also drop spare tire to allow room to raise hitch in place.
2. From underneath the truck, locate the large hole in truck cross-member above rear axle. Using this hole as a guide insert
the 3-1/4" hole - saw up through and drill so that only the 1/4" pilot bit in the hole-saw drills through truck bed. Then
from above the truck bed, drill back down with 3-1/4" hole-saw to enlarge. File edges and touch up with paint or a sealer
so as not to rust.
3. Remove retaining screws from rear wheel-wells so as to insert nut plate assembly above truck cross-member below truck
bed, typical both sides. Caution: Nut plate to be installed over electrical harness on drivers side (Picture 1. Below)
4. From underneath truck, lift head into position and attach with supplied M16 bolts, washers and blocks. Torque bolts to
230 ft. lbs. (Figure 1. Page 1.)
5. Using the safety chain U-bolt holes in the hitch as a guide, use an 11/16" drill or transfer punch to locate center of holes.
Drill a 3/16" pilot hole up thru frame cross member and bed. Make sure drill is straight. From in the bed drill down with
an 5/8" drill bit. Touch up all drilled holes with a file and paint or sealer. Drop U-bolts down through these holes from
above. (Figure 2. next page)
6. From under the truck, install the 9/16" flat washers, springs, and 5/8" jam nuts (See Figure 1.). Before tightening jam
nuts lift U-bolts up and down from inside bed to assure smooth operation. If not then enlarge holes as necessary. Tighten
jam nuts so a minimum of 3 threads are showing beyond the nuts.
7. Replace retaining screws in wheel well, bend wire handle if necessary. Reinstall exhaust hangers.
Remove (2) screws to ease
installation – not required
Caution:
Elecrtical harness – drivers side
AFTER HITCH INSTALLATION AND BEFORE TOWING:
Connect trailer to the tow vehicle following coupler manufacturer's operating instructions.
The coupler must be adjusted to provide about 6" of clearance between the bottom of the trailer nose and the top of the
pickup bed sides. Using another person to view slowly back the trailer to a jackknifed position relative to the tow vehicle
in both directions to check for adequate clearances. Between the gooseneck trailer and the rear of the truck and also
check to see there is adequate clearance between the forward corners of the trailer and the rear of the truck cab.
GOOSENECK MAINTENANCE:
Use cover to keep hitch free of dirt and debris. Lubricate ball sleeve with oil when ball is installed or removed. Before
you tow, check that the hitch ball is locking properly in hitch sleeve every time. Do not leave hitch ball in hitch when not
towing. Check bolt torque monthly. Check equipment before towing for worn or damaged parts.
© © © © 2014 Cequent Performance Products
Hide-A-Goose
Installation Instructions, Ram 2500
Picture 1.
REPLACE WORN OR DAMAGED PARTS IMMEDIATELY.
TM
Do Not Exceed
Lower of Towing Vehicle Manufacturer's Rating or:
20,000 LB
(9080Kg) Max Gross Trailer Weight (GTW)
5000 LB
(2270 Kg) Max Tongue Weight (TW)
Looking up at bottom of truck bed
Rear axle breather hose will have to be relocated
before installing hitch and drilling for safety chain
u-bolts. Relocate hose by pulling clip off of cross-
member and locating in another location.
Sheet 2 of 12 9467N
Part Numbers:
9467
Picture 2.
4-15-14 Rev. A