Campbell Hausfeld WG2040 Manual De Instrucciones De Operación Y Partes página 6

Wire Feed Arc Welder
Assembly
(Continued)
HOOKUP PROCEDURE (Continued)
counterclockwise. When gas is
emitted from cylinder, close valve by
turning clockwise. This will blow out
dust or dirt that may have
accumulated around valve seat.
2. Install regulator onto cylinder valve.
Tighten stem nut securely to gas
valve.
3. Install one end of gas hose to fitting
on the rear of welder and other end
of hose to fitting on regulator using
hose clamps on each connection. Make
sure gas hose is not kinked or twisted.
4. While standing opposite cylinder
outlet, slowly open cylinder valve.
Inspect for leaks in the connections.
5. Pull trigger on gun to allow gas to
flow. Adjust gas regulator to
maximum flow by moving clockwise.
Release trigger.
6. Remember to close gas cylinder valve
when finished welding.
Handshield
Assembly
Figure 9
1. Cut retainer stiffeners and detachable
handle away from shield. Trim the
excess plastic to remove sharp edges.
2. Insert filter lens.
3. Attach the stiffeners over the pins on
the lens retainers (See Figure 9).
Figure 10
www.chpower.com
4. To attach the handle, place shield on
a flat surface and press handle into
place (See Figure 10).
NOTE: If you have never welded
before or have little experience, a
full face helmet is recommended.
Both hands are needed to stabilize
and control the angle and arc
length of the torch.
Welding Helmet
Assembly
Models Only)
Stud Screw (2)
Tension Nut (2)
Adjustment
Arm (2)
Lens Retainer
Post
Figure 11
1. Remove the lens retainer from the
face shield with a regular screwdriver
Lens
by prying against the shield and post
of the lens retainer.
2. Remove the protective film covering
Lens
from both sides of each lens cover.
Retainer
Put one clear lens cover on each side
of the shaded lens. Place these three
Retainer
lenses together into the face shield
Stiffener
and secure with the lens retainer. The
lens retainer should snap into the
second notch in the face shield.
3. Position one of the holes in the
adjustment arm over the pins which
are located in the ear area of the face
shield. These adjustment arms control
the closeness of fit and can be easily
repositioned if necessary.
4. Position the headgear inside the face
shield. Assemble the helmet by
inserting the stud screw through the
headgear and shield into the tension
nut as shown. Do not tighten tension
nut completely.
5. Trial fit the welding helmet. Adjust
headgear ratchet band to a
comfortable position and lower the
face shield. If the shield is too far or
Operation
1. Be sure to read,
(Promotional
Headgear
2. Turn welder off.
3. Verify surfaces of metals to be joined
Face Shield
!
equipment or in the area while
equipment is in use must wear
protective welding gear including: eye
Shaded Lens
protection with proper shade, flame
resistant clothing, leather welding
Clear Lens Cover (2)
gloves and full foot protection.
!
If heating, welding or
cutting galvanized, zinc
plated, lead, or cadmium
plated materials, refer to
the General Safety
Information Section for instructions.
Extremely toxic fumes are created when
these metals are heated.
4. Connect work clamp to work piece or
5. Position Heat Selector on front panel
24 - 14 Gauge (MIG only)
18 - 14 Gauge (Flux Core)
Thicker Than 14 Gauge
NOTE: These settings are general
guidelines only. Heat setting may vary
according to welding conditions and
materials.
6
too close to the face, use a different
hole in the adjustment arm. Adjust the
tension nuts so that helmet can be
easily lowered over the face by
nodding the head.
understand and comply
with all precautions in
the General Safety
Information section. Be
sure to read entire
"Welding Guidelines" section before
using this equipment.
are free from dirt, rust, paint, oil,
scale or other contaminants. These
contaminants make welding difficult
and cause poor welds.
All persons
WARNING
operating this
WARNING
workbench (if metal). Make sure
contact is secure. Avoid surfaces with
paint, varnish, corrosion or non-
metallic materials.
to desired setting.
Metal
Thickness
MANUAL
Heat
Setting
Low 1 or 2
High 1 or 2