Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation Instructions
Installation Instructions
Please Read Before Installing
Please Read Before Installing
Overview
The 4 Series Processors, model numbers H4P5-H48-
120, H4P5-H48-HRL-120, H4P5-120, and H4P5-HRL-
120, have three (3) configurable communication links
allowing connection of HomeWorks Wired Keypads,
HomeWorks Wired Maestro
HomeWorks Wallbox Power Modules, and SOLos
Homeworks/Sivoia QED
Integrators. Model numbers
TM
H4P5-H48-HRL-120 and H4P5-HRL-120 have an
additional dedicated link for Hybrid Repeaters, allowing
expansion to RF devices. The central processor provides
lighting presets, astronomic timeclock events, security
mode, vacation mode, conditional logic, and all other
HomeWorks programming functions.
A maximum of 10 seeTouch
150 LEDs) may be powered by Link 6 on the 4 Series
Processor. To power additional keypads, or to use
keypads on Links 4 or 5, an additional power supply is
required (Lutron model # T120-15DC-9-BL).
The dedicated Hybrid Repeater Link (Link 8) on H4P5-
H48-HRL-120 and H4P5-HRL-120 processors can provide
power to Hybrid Repeaters. Each Hybrid Repeater counts
as 30 LEDs towards the maximum of 150 LEDs.
Important Notes
Codes: Install in accordance with all local and
national electrical codes.
Power: Two separate power inputs exist on this
processor:
1. Processor power is provided by the 2 conductor
harness that is integral to the HWI-LV24 enclo-
sure. The processor is powered when the green
LED labeled "PWR" is on.
2. Keypads connected to Link 6 are powered by the
supplied plug-in adapter connected to the power
jack labeled "Link 6 15 V
properly when the green "LINK PWR" LED is on.
If the red "LINK SHORT" LED is on, Link 6 or 8 is
shorted (between terminals 1 and 2) or
overloaded (exceeding 150 LEDs).
Both Processor power and Link 6 and 8 power must
be present for the processor and keypads to function
properly.
Local Lighting Controls,
®
TM
keypads (equivalent to
TM
". Link 6 is powered
4 Series
Processor
TM
H4P5-H48-120, H4P5-H48-HRL-120
H4P5-120, H4P5-HRL-120
12 V
60 Hz 30 W
H4P5-H48-120 H4P5-H48-HRL-120
Plug-in Adapter
T120-15DC-9-BL
Input: 120 V
60 Hz 19 W
Output: 15 V
900 mA
NEC Class 2; IEC PELV
Figure 1 - 4 Series Processors and Adapter
Processor Power: 12 V
Link 6 and 8 Power: 15 V
NEC Class 2; IEC PELV
Use only the adapter provided by Lutron with
the 4 Series Processor (Lutron model # T120-
15DC-9-BL).
Environment: Ambient operating temperature:
0-40°C, 32-104°F, 0-90% humidity, non-condensing.
Indoor use only.
Cleaning: To clean, wipe with a clean damp cloth. DO
NOT use any chemical cleaning solutions.
H4P5-120
H4P5-HRL-120
30 W
900 mA
1
Publicidad
Tabla de contenido
Manuales relacionados para Homeworks 4 Series
Resumen de contenidos para Homeworks 4 Series
- Página 1 A maximum of 10 seeTouch keypads (equivalent to NEC Class 2; IEC PELV 150 LEDs) may be powered by Link 6 on the 4 Series Processor. To power additional keypads, or to use Figure 1 - 4 Series Processors and Adapter keypads on Links 4 or 5, an additional power supply is required (Lutron model # T120-15DC-9-BL).
- Página 2 10.Connect power. Plug the power input harness terminals (blue wires) from the HWI-LV24 enclosure onto the power feed lugs on the 4 Series Processor. Connect plug Figure 3 - Processor Addressing from adapter to Link 6/8 Power connector. Plug adapter...
- Página 3 HWI-LV24. The 4 Series programming the system via direct connection to a Processor has battery-backed memory and timeclock laptop computer. If plugging into a network, a standard devices. The battery provides power to these devices cable is used (see Figure 4, below).
-
Página 4: Technical And Sales Assistance
Fax: +1.610.282.3090 are registered trademarks and 8 Series, 4 Series, Illumination, seeTouch, SOLos, Sivoia QED, and the HomeWorks 4 Series logo are trademarks of Lutron Electronics Co., Inc. Visit our Web site at www.lutron.com © 2005 Lutron Electronics Co., Inc. -
Página 5: Instrucciones Para La Instalación
Figura 1 - Procesadores 4 Series y Adaptador a 150 LEDs) pueden ser alimentados por el Vínculo Vínculo 6 en el Procesador 4 Series. Para alimentar botoneras adicionales, o para usar botoneras en los Vínculos 4 o 5, se requiere una fuente adicional de ali- mentación (Lutron modelo # T120-15DC-9-BL). -
Página 6: Instalación
CCO-8) que deben ser controlados por este Procesador, conecte los cables de comunicación al(los) Vínculo(s) 4, 5, o 6 como se configuraron con el software HomeWorks Illumination. Nota: La conexión de las botoneras o los dispositivos de vínculo de las botoneras distintos del Vínculo 6 requieren una fuente de alimentación adicional. - Página 7 HWI-LV24 hasta los montantes de alimentación procesador para la programación o las comunicaciones en el Procesador 4 Series. conecte el enchufe del adap- del sistema con otro equipamiento. Un cable cruzado se tador al conector de alimentación del Vínculo 6/8.
-
Página 8: Asistencia Técnica Y Comercial
GRAFIK Eye, Maestro y HomeWorks son marcas comerciales registradas y 8 Series, 4 Fax: +1.610.282.3090 Series, seeTouch, Illumination, SOLos, Sivoia QED, y el logo de HomeWorks 4 Series son marcas comerciales de Lutron Electronics Co., Inc. Visite nuestra página Web: http://www.lutron.com ©... -
Página 9: Vue Générale
(équivalent à150 DEL) peuvent être alimentés par la liaison 6 sur le Figure 1 - Processeurs 4 Series et Adaptateur processeur 4 Series. Pour alimenter des claviers additionnels, ou pour utiliser des claviers sur la liaison 4 ou 5, une source d’alimentation additionnel est requise (Lutron... - Página 10 Illumination alertera le programmeur si un changement HomeWorks. Connecter le câblage de commande à la liaison ultérieur aux commutateurs de configuration est requis. inter-processeur (liaison 2), s’il y a lieu. Ne pas connecter (voir table 2).
- Página 11 à un autre appareil sans con- 6 Réception -ve Transmission -ve 7 NC centrateur (système a/v, HVAC, 7 Pas de connexion Pas de Connexion 8 NC etc.) 8 Pas de connexion Pas de Connexion Figure 4 – Processeur 4 Series...
-
Página 12: Garantie Limitée
Maestro, et HomeWorks sont des marques déposées enregistrées et 8 Series, 4 Series, Télécopieur : +1.610.282.3090 seeTouch, Illumination, SOLos, Sivoia QED, et le logo de HomeWorks 4 Series sont des mar- ques déposées de Lutron Electronics Co., Inc. Visiter notre site web au www.lutron.com ©... -
Página 13: Instruções De Instalação
Visão geral H4P5-H48-120 H4P5-H48-HRL-120 H4P5-120 H4P5-HRL-120 Os processadores 4 Series, números de modelo H4P5- H48-120, H4P5-H48-HRL-120, H4P5-120, e H4P5-HRL-120, possuem três (3) links de comunicação configuráveis que permitem a conexão de teclados com fio HomeWorks, controles de iluminação local HomeWorks com fio Maestro e módulos de força de caixa de embutir... - Página 14 3. Defina o endereço do processador. Defina o endereço HomeWorks. Conecte a fiação de controle ao link inter- do processador usando a chave de configuração. O software processador (link 2), se necessário. Não conecte o terminal HomeWorks Illumination avisará...
- Página 15 HWI-LV24 nos plugues de alimentação tador de modem nulo será necessário entre de energia ao processador 4 Series. Conecte o plugue o processador e o modem. do adaptador ao conector de alimentação do link 6/8.
- Página 16 GRAFIK Eye, Maestro, e HomeWorks são marcas comerciais registradas e 8 Fax: +1.610.282.3090 Series, 4 Series, seeTouch, Illumination, SOLos, Sivoia QED, e o HomeWorks 4 Series logotipo são marcas comerciais da Lutron Electronics Co., Inc. Visite nosso site na Internet www.lutron.com ©...