Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
7200
SETTINGS
Ringtone volume and melody selection functions
These settings can be adjusted with the display switched off. Press pu-
sh-button
(self-start) for 2 seconds, until the green LED
bottom right flashes. This LED is normally used to indicate DOOR OPEN.
This flashing indicates "SETTING" mode, during which buttons
can be used to adjust the ringtone volume and push-buttons
and
to select the melody.
The monitor will remain in "SETTING" mode (green LED flashing) until the
arrow buttons are pressed. SETTING mode is cancelled when the arrow
buttons are not pressed for more than 5 seconds. Nevertheless the user can
exit this mode by pressing button
tches off.
Ringtone mute function
Ringtone mute is activated using the same procedure described above for
adjusting the ringtone volume. Once the volume has been adjusted to the
lowest setting by repeatedly pressing the down arrow, the red LED
the bottom left-hand corner illuminates to indicate that ringtone mute is acti-
vated.
Brightness and contrast control functions
These settings can be adjusted with the display switched on. Press pu-
sh-button
(self-start) for 2 seconds, until the green LED
the bottom left flashes. This LED normally serves as the OPEN DOOR indi-
cator. This flashing indicates entry into "SETTING" mode, during which but-
tons
and
can be used to set the contrast and buttons
and
to select the brightness. When the maximum and minimum
values are reached, this is indicated by a beep. The monitor will remain in
"SETTING" mode (green LED flashing) until the arrow buttons are pressed.
SETTING mode is cancelled when the arrow buttons are not pressed for
more than 5 seconds. Nevertheless the user can exit this mode by pressing
button
again until the green LED switches off.
Communication mode selection function (
It is possible to choose between two different modes of communication with
speech units or intercom devices:
1. HANDS FREE mode: press the TALK/LISTEN push-button
start of the conversation only, to activate the audio, and at the end of the
conversation to deactivate the audio. The "audio active" condition is indi-
cated by the illumination of the red LED
the monitor, which is normally used to indicate RINGTONE MUTE.
2. PUSH-TO-TALK mode: keep the talk/listen push-button
during the conversation; release it at the end of the conversation.
The 7200 series monitor is factory set to HANDS FREE communication
mode. To switch from one mode to the other, with the monitor switched OFF
press push-button
for 2 seconds to enter SETTING mode; simul-
taneously press and hold down push-buttons
red LED
underneath starts flashing. At this point, while the LED is
flashing, press the TALK/LISTEN push-button
change. The function is confirmed if the red LED switches off.
EN
at the
and
again until the green LED swi-
in
at
button)
at the
at the bottom left corner of
pressed
and
until the
. to confirm the
Automatic answer function
This function, which is only available in HANDS FREE mode, activates the
monitor audio connection automatically when a call is received from the
speech unit or intercom device, without the need to push the TALK/LISTEN
button
. The "audio active" condition is indicated by the illumination
of the red LED
at the bottom left corner of the monitor, which is nor-
mally used to indicate RINGTONE MUTE. The audio is activated automati-
cally 5 seconds after the call is received. To enable this function, with the
monitor switched OFF press push-button
SETTING mode; simultaneously press and hold down push-buttons
and
until the red LED underneath starts flashing. At this point,
while the LED is flashing, press the TALK/LISTEN push-button
confirm the change. The function is confirmed if the red LED switches off.
To disable this function, follow the same procedure. If HANDS FREE mode
was not active during the enabling process, it will be activated automatically
when the AUTOMATIC ANSWER function is enabled. If the automatic an-
swer function is subsequently disabled, the HANDS FREE function will re-
main active.
Adjusting the conversation volume
The term "conversation volume" refers to the perceived volume of the cal-
ler's voice when he/she is standing in front of the speech unit (entrance
panel), or speaking through an intercommunicating interphone or monitor.
To adjust the conversation volume, the user must be in communication with
a speech unit or intercom device. Press push-button
to enter SETTING mode; once the green LED
and hold the TALK/LISTEN push-button
push-buttons
and
FREE mode and in PUSH-TO-TALK mode.
Push-buttons
,
,
These four push-buttons can be programmed to perform up to 4 functions
including intercom calls and auxiliary commands, when the monitor is not in
setting mode. By default, push-button
command, push-button
sh-button
with F2.
Push-button
is not associated with any command. To program pu-
sh-button
or to change the function of push-buttons
or
, use programmer type 950C or the SaveProg software
for PC, except for assigning the functions of intercommunicating calls and
self-start service to a specific panel, as described below in the paragraph
"Programming push-buttons".
for 2 seconds to enter
for 2 seconds
starts flashing, press
and adjust the volume with
. This procedure applies both in HANDS
and
is associated with the AUX 2
is associated with the F1 command, pu-
to
,
,
11
Publicidad
Tabla de contenido
