(P/N 88576) - Alder USV-6-80T Manual De Servicio

ITEM QTY P/N:
51 1 88326
52 1 88327
53 1 88328
54 1 89122
55 1 89123
56 1 89318
57 1 89319
58 4 89482
59 1 90678
60 1 90692
61 1 90693
62 1 90695
63 1 90710
64 1 90722
65 1 90789
66 3 90796
67 1 90798
68 2 90800
69 4 90801
70 1 90802
71 2 90814
72 1 90821
73 1 90846
74 1 90907
75
1 90909
76 1 90910
77 1 90911
78 1 90912
79 1 90913
80 1 90914
81 1 90915
82 1 90916
83 1 90917
84 1 90926
P/N 90926-S, Rev. 0
HOSE ASSY .23 ID 3/8 NPTM SS X 3/8 NPTM SS X 108.96 IN OAL 17.4KSI (6/2WL)
HOSE ASSY .39 ID 3/8 NPTM X 3/8 NPTM X 44.78 IN OAL 15KSI (10/2W)
HOSE ASSY 3 KSI 3/8 NPTM X 54.9 OAL STRAIGHT ENDS
LABEL CAUTION - DO NOT REMOVE LIFTING DEVICE 4-5/8 X 3-1/4
LABEL CAUTION - DO NOT CRAWL UNDER 4-5/8 X 3-1/4
HOSE ASSY .23 ID 1/4 NPTM SS X 9/16 FEM TYPE M SS X 240 IN OAL 17.4KSI (6/2WL)
HOSE ASSY .50 ID 1/2 NPTM SS X 1-12 FEM TYPE M SS X 240 IN OAL 15KSI (13/2W)
SCREW 1/2-13 X 1-3/4 HHCS SS
LABEL CLAMPING CHART USV-6-80T
CONSOLE CONTROL USV 8600 PSI CLAMP W/ TILT
WELDMENT CLAMP BOX MODEL USV-6-80T
WELDMENT BASE FRAME USV-6-80T
RAM HYDRAULIC 100 TON 24 INCH STROKE
CYLINDER COLLAR MODEL USV-6-80T
TROLLEY WELDMENT MODEL USV-6-80T
SCREW 1/2-13 X 4-1/2 HHCS SS
SWIVEL RING MODEL USV-6-80T
BAR TROLLEY MODEL 600 80 TON
SCREW 1 DIA X 3-1/2 X 3/4-10 SHLDCS SS
TOP PLATE BRACKET 80T
BRG PILLOW BLOCK 1-1/4 DIA
NUT 1-8 STDN ZINC PLATED
KIT - FIXED SEAL PLATES MODEL USV-6-80T
CYLINDER HYDRAULIC 2.5 BORE X 16 STROKE 3/8 NPT INLINE RED
TUBE 1/2 SUPER DUPLEX CYLINDER PORT UPPER CLAMP FIXTURE MODEL USV 80
TUBE 1/2 SS CYLINDER PORT LOWER CLAMP FIXTURE MODEL USV 80
TUBE 1/2 SUPER DUPLEX CLAMP BOX FIXTURE MODEL USV 80
TUBE SS 1/2 CLAMP BOX MODEL USV 80
TUBE 1/2 SUPER DUPLEX BOTTOM PLATE CLAMP FIXTURE MODEL USV 80
TUBE SS 1/2 CONSOLE TO FRAME USV 80
TUBE 1/2 SUPER DUPLEX CONSOLE TO FRAME USV 80
TUBE 1/2 SUPER DUPLEX INLET BOTTOM PLATE CLAMP FIXTURE USV 80
TUBE 3/8 SUPER DUPLEX INLET BOTTOM PLATE CLAMP FIXTURE USV 80
(NOT SHOWN) MANUAL INSTRUCTION USV-6-80T
F A-4. USV-6-80T
IGURA
PARTS LIST
DESCRIPTION
MONTAJE DE MORDAZA CON INCLINADO
SCHEMATIC ID
,

2 (P/N 88576)

LISTA DE PIEZAS
C-01
C-10
Página 39