Jump Starting; Sequence Of Operations - Deca Fast 35k Manual De Instrucciones

received dents, if it has been dropped or if it has been
damaged.
„ Do not use the appliance if during use, charge or
conservation the battery smells, heats up, or deforms or
has acid leaks.
„ Do not disassemble the appliance but take it to a qualified
service centre.
„ Clean the appliance with a dry cloth. Do not use solvents
or other detergent aggressive substances.
„ Store the appliance at ambient temperature (20 - 25 °), keep
it away from direct sunlight and away from heat sources.
Description of the starter
This appliance is a portable multifunction starter equipped
with a lithium battery.
It can be used as an emergency starter for motor vehicles It can be used as an emergency starter for motor vehicles
with 12 / 24-volt electrical system; it can recharge / supply 5V, with 12 / 24-volt electrical system; it can recharge / supply 5V,
12V electronic devices. 12V electronic devices.
It is equipped with a LED light with the function of continuous, It is equipped with a LED light with the function of continuous,
intermittent, SOS light. intermittent, SOS light.
Controls, reports and accessories Fig.1 Controls, reports and accessories Fig.1
A) Multifunction Starter A) Multifunction Starter
B) Power supply unit 100 - 240V B) Power supply unit 100 - 240V
C) Multi USB Cable C) Multi USB Cable
1) Key ON / OFF for USB ports, led light. 1) Key ON / OFF for USB ports, led light.
2) KEY OVER RIDE, 12V, 24V 2) KEY OVER RIDE, 12V, 24V
3) Output USB port for power supply 5V, 1A; 5V2A 3) Output USB port for power supply 5V, 1A; 5V2A
4) Screen 4) Screen
5) Input port for charging 15V, 1A 5) Input port for charging 15V, 1A
6) Cable with clamps for jump starting 6) Cable with clamps for jump starting
7) LED light 7) LED light
8) Output port for power supply 12V, 10 8) Output port for power supply 12V, 10

Jump starting

Use the appliance only as an emergency starter
to support the vehicle battery. Do not use it alone
instead of the battery.
„ Avoid the formation of flames or sparks. To avoid sparks,
make sure that the clamps cannot disengage from the poles
of the battery during charging.
„ Stay away from moving parts such as fans, transmission
belts and pulleys.
„ Stay away from hot parts, such as engine and cooling
system to avoid burns.
„ Do not short circuit the terminals for the emergency start
cable because they are always under tension.
„ Avoids that the red and black clamps come into contact.
Accidental short circuits of the terminals caused by an
electrical conductor object for example a tool, a jewel, etc.
could generate enough heat to cause serious burns, electric
arc or cause incandescent metal splashes.
„ Do not reverse the polarity of the positive "+" negative and
"-" terminals

Sequence of operations

Starter battery must be fully charged (4 led lit).
Carefully follow the starting procedure, failure to refully follow the starting procedure, failure to
comply may affect the life of the appliance. comply may affect the life of the appliance.
The starter automatically recognizes the presence The starter automatically recognizes the presence
of the battery and its voltage (12V / 24V). Do not use of the battery and its voltage (12V / 24V). Do not use
the "Over Ride" function unless the starter fails to the "Over Ride" function unless the starter fails to
recognize the battery. recognize the battery.
950701-01 18/02/21
1 1 Make sure that the vehicle ignition key is in the OFF Make sure that the vehicle ignition key is in the OFF
position: all services turned off. position: all services turned off.
2 2
Connect red charging clamp to positive Connect red charging clamp to positive (+)
terminal and black charging clamp (-) (-) to negative terminal and black charging clamp
battery terminal. battery terminal.
If the battery is installed on a motor vehicle, first If the battery is installed on a motor vehicle, first
connect the clamp to the battery terminal that is not connect the clamp to the battery terminal that is not
connected to the bodywork. Afterwards, connect the connected to the bodywork. Afterwards, connect the
second clamp to the bodywork at a point far from both second clamp to the bodywork at a point far from both
the battery and the petrol pipes. the battery and the petrol pipes.
When the connection is correct the display shows the When the connection is correct the display shows the
message "Jump start ready 12V" or "Jump start ready message "Jump start ready 12V" or "Jump start ready
24V". The starter is ready. 24V". The starter is ready.
3 3 Rotate the ignition key for up to 3 seconds. Rotate the ignition key for up to 3 seconds.
If the vehicle did not start wait at least 15 seconds If the vehicle did not start wait at least 15 seconds
before trying again. before trying again.
¾ Repeated start attempts may activate the starter's thermal
protection. Wait 500 seconds before re-starting, as indicated
on the display.
¾ If the vehicle battery is near sulphation or is faulty, the control
unit may not activate the starting procedure. The starter will
not supply the power needed to start the vehicle. The starter
will remain in standby mode.
¾ ¾ Make sure the battery is not faulty and proceed to carry Make sure the battery is not faulty and proceed to carry
out a minimum charge of the battery with a charger before out a minimum charge of the battery with a charger before
using the starter. using the starter.
¾ ¾ After starting leave the engine running and disconnect After starting leave the engine running and disconnect
the starter: the starter:
¾ ¾ Disconnect in the order the black clamp "-" and then the Disconnect in the order the black clamp "-" and then the
red clamp "+". red clamp "+".
¾ ¾ Disconnect the cable with the clamps from the starter and Disconnect the cable with the clamps from the starter and
put everything into its box. put everything into its box.
OVER RIDE FUNCTION
If the vehicle battery is completely discharged, the starter is
not able to recognize the battery voltage.
The user must recognize the battery, correctly connect the (+)
(-) terminals and adjust the starter.
Carefully check the battery voltage (12V / 24V) in
order to not damage the electrical system of the
vehicle
1
Make sure that the vehicle ignition key is in the OFF
position: all services turned off.
2 2 Connect red charging clamp to positive (+) battery Connec
terminal and black charging clamp (-) to negative
battery terminal.
If the battery is installed on a motor vehicle, first
connect the clamp to the battery terminal that is not
connected to the bodywork. Afterwards, connect the
second clamp to the bodywork at a point far from both
the battery and the petrol pipes.
3
Press the button "Over Ride" (2)
4 Press the button "12V" or "24V"(2) for at least 2
seconds
The display shows the message "Jump start ready
12V" or "Jump start ready 24V"
Start the engine within 30 seconds.
5
Rotate the ignition key for up to 3 seconds. Rotate the ignition key for up to 3 seconds.
If the vehicle did not start wait at least 15 seconds
before trying again.
Use as power supply USB / 12V
1 Briefly press the key (1): the display shows the
5
(+) battery
battery
to negative