Programming The Delay Brew Time; Precision Temp Warming Plate; Care & Maintenance; Cleaning After A Brew - Ninja CE200 Serie Manual Del Propietário

Fig. 7

PROGRAMMING THE DELAY BREW TIME

1
With Power on, press DELAY BREW.
The DELAY BREW button will illuminate
and the clock will flash "12:00" or the last
Delay Brew time that was set (Fig. 7).
2 While the clock is flashing, use the H and
M buttons to set the time you would like
the Delay Brew to begin. The AM or PM
indicator will illuminate on the left side of
the display as you are setting the desired
time.
3 Select desired brew style and selection
will illuminate (Fig. 8).
4 Once the time, brew size, and brew
type have been set, press the DELAY
BREW button again to activate, or wait
five seconds for the brew time to lock
in automatically. The unit will beep to
indicate the brew time has been set,
and the DELAY BREW button will
remain illuminated.
NOTE: To deactivate the Delay Brew
cycle, press the DELAY BREW button
once more and the light on the button
will turn off. Any change to the selected
brew size or starting any other brew will
cancel the programmed Delay Brew.
Turning off the unit will also cancel the
Delay Brew.
5 Place the carafe under brew basket.
NOTE: The Ninja® Coffee Brewer must
remain on for the Delay Brew function
to work. DO NOT power off after setting
the Delay Brew time.
9
Fig. 8 Fig. 9

PRECISION TEMP WARMING PLATE

The warming plate will turn on once
the brew has started. Press the STAY
WARM button after the brew to turn off
the warming plate (Fig. 9). You can turn
the warming plate back on by pressing
the STAY WARM button again. Wait until
surface has cooled completely before
touching.
NOTE: DO NOT add additional
water to the reservoir when using
the STAY WARM function.
You can program the warming plate to stay
on for up to 4 hours.
1
Press and hold STAY WARM button until
the clock flashes, displaying the time at
which the warming plate is currently set
to turn off.
2 Quickly press the hour (H) or minute (M)
button to adjust the time up to 4 hours.
The warming plate is automatically
programmed to stay on for 2:00 hours.
3 To lock in the new duration, press the
STAY WARM button again, or wait 5
seconds for it to lock in automatically.
CARE & MAINTENANCE

CLEANING AFTER A BREW

1 After each brew is complete and the
coffee grounds have cooled, discard the
paper filter. Take out the removable filter
holder, rinse, and wash with soap and
warm water. If using a permanent filter,
dump the grounds into the trash and
wash the filter by hand with warm, soapy
water or place on the top rack of the
dishwasher.
NOTE: If coffee grounds spill over into
the filter holder, remove the filter holder
and rinse it.
2 We recommend cleaning your
carafe with warm, soapy
water, or placing it on
the top rack of your
dishwasher. If you want
to clean the carafe more
thoroughly, we recommend
using a soft foam brush such
as the one shown to the right.
a Empty the water reservoir.
b Hand-wash with dish soap and
rinse or place on the top rack of
your dishwasher.
3 Unplug your unit and let the warming
plate cool before cleaning. Wipe down
with a soft cloth and warm water.
DO NOT immerse the base in water.
DESCALING YOUR
NINJA® COFFEE BREWER
1
Use a descaling solution specifically
formulated for coffeemaker cleaning and
follow the directions on the package.
Fill the water reservoir up to, but not
exceeding, the 12-Cup Line (60 fl. oz.).
OR
Add 16 oz. of white vinegar to the water
reservoir, then fill the rest of the reservoir
with water up to, but not exceeding, the
12-Cup Line (60 fl. oz.).
2 Once the water reservoir is filled with
your cleaning solution or vinegar mixture,
press the CLEAN button. The clean cycle
takes approximately 25–35 minutes. To
cancel the clean cycle, either press the
CLEAN button again or press the
Power button.
3 The unit will beep when the clean cycle
successfully completes. Refill the reservoir
with fresh water up to, but not exceeding,
the 12-Cup Line, and set the empty carafe
beneath the brew basket. Run a full Classic
Brew cycle with water only to remove any
cleaning solution that could affect the
flavor of your coffee.
NOTE: Make sure the SMALL BATCH
button is not selected/illuminated and
set the empty carafe beneath the brew
basket.
ninjakitchen.com 10