Publicidad
Idiomas disponibles
Idiomas disponibles
Special Notes:
• The same scene can be programmed into multiple buttons if desired.
• Multiple scenes may be launched, and will each illuminate their own LED.
• During programming a failure to transfer the selected scene will be indicated on the Cooper Wiring
Devices' controller screen. If this occurs repeat the programming steps.
• The pressing of any additional buttons while the scene information is being down loaded will cause
the scene to be dropped. You will need to redo the programming sequence.
• While RFTDCSG or RFHDCSG is in the Send mode, if a scene button is not selected within 5 seconds
either RFTDCSG or RFHDCSG will revert back to the Main Menu.
LAUNCHING SCENES:
The pressing of a programmed scene button will activate the pre-programmed scene. The scene LED will
illuminate and provide an indication that this scene was turned on.
Pressing a scene button that has already been turned ON will then turn all devices in that scene OFF. This
provides convenient single button ON/OFF control for each programmed scene button.
If you press a non-programmed scene button you will not launch any scene. As an indication that the
scene button has not yet been programmed the selected button's LED will come on for one second,
and then go off.
DIMMING A SCENE:
Any launched scene (scene button LED is ON) can be dimmed or brightened by pressing and holding
the scene button.
First, press and hold the scene button to dim the scene. Releasing the scene button will stop the
adjustment of the light level.
Second, press and hold the scene button to brighten the scene. Releasing the button will stop the
adjustment of light level. If you press and hold, the scene will dim or brighten to the point that all the
lights included in that scene will go to the minimum or maximum brightness level.
"ALL OFF" FEATURE:
This is a convenient feature when leaving the home, or an area, that allows for all devices controlled by
that RFWC5 to be turned off with the touch of a single button.
The 6th button, offset from the 5 button set, provides the "ALL OFF" feature.
No programming is required for this feature.
When the "ALL OFF" button is pressed for 2 seconds, the LEDs will blink to acknowledge that the button
has been pressed for 2 seconds, and then all devices programmed to this individual scene controller will
turn off. All scene button indicator LEDs will also turn off.
ERASING SCENES:
A scene can be over written by following the steps defined above. The new scene will simply replace
the old scene.
The RFWC5 can also be reset such that no buttons are programmed with the following steps.
1. Press and hold buttons 1 and 5 until all LED's begin to blink. Release buttons 1, and 5.
2. Now press and release the All OFF button to complete the Reset of the RFWC5.
3. The LED's will stop blinking when the RFWC5 reset is complete.
NOTE: The pressing of any other button while the RFWC5 is in the ready-to-reset mode will cause the
RFWC5 to come out of the reset mode. This feature helps prevent inadvertent erasure.
UNINSTALLING THE RFWC5:
A Cooper Controller can be used to uninstall the RFWC5 regardless of whether it was the original
Controller that installed the device. If you experience problems uninstalling the RFWC5 with a non-
Cooper Controller, you can uninstall the RFWC5 by performing a factory reset with the following proce-
dure. This will completely erase all scenes programmed in the RFWC5.
1. Press and hold buttons 1, 3 and 5 for 5 seconds at the same time. DO NOT press any other scene
controller buttons at this time. Release buttons 1, 3 and 5.
2. While in this state press and release the "ALL OFF" button. The successful reset of the RFWC5
will be indicated on the device by the continuous blinking of all 5 LED's.
La commande murale 5 scènes (RFWC5) est une commande à
fréquences radio ASPIRE RF™ qui permet à l'utilisateur d'activer des
scènes pré-réglées en appuyant sur un seul bouton. Elle comprend cinq
boutons qui peuvent activer cinq scènes individuelles ainsi qu'un 6e
bouton qui sert à tout
éteindre (ALL OFF).
Il est nécessaire de se servir d'une commande de table à fréquences
radio ASPIRE RF (RFTDCSG) ou d'une commande portative (RFHDCSG) de
Cooper Wiring Devices pour créer des scènes et les transférer sur le
RFWC5.
Le RFWC5 peut être placé dans l'entrée ou dans un lieu pratique d'où on
désire commander des scènes multiples. Les scènes sont des groupes de
réglages pré-configurés sur les appareils individuels (interrupteurs, prises,
gradateurs, etc. ).
FRANÇAIS
Publicidad
