Pelican SabreLite 2000 Instrucciones De Funcionamiento

SabreLite
TM
OPERATING INSTRUCTIONS
BATTERY INSTALLATION
1. Remove lens housing by turning counter-clockwise.
2. Remove the lamp module.
3. Remove the battery tray.
4. Remove used batteries and replace with fresh batteries in the tray as
shown by the polarity icons molded into the base of the tray battery.
5. Insert the battery tray into the flashlight with the two metal tabs fac-
ing outwards.
6. Replace the lamp module.
7. Replace lens housing squarely on threads and turn
clockwise while pressing on the lens housing slightly.
ON/OFF
Turn the lens housing clockwise until light activates.
To turn light off, back lens housing off counter-clockwise until light goes
off. Continue to back off for approximately 1 full turn to eliminate possibil-
ity of light activating accidentally in storage. DO NOT OVERTIGHTEN.
LAMP REPLACEMENT
To replace the lamp module follow steps in the
battery installation section as listed below:
To remove lamp module follow steps #1 and #2.
To replace lamp module follow steps #6 and #7.
WARNING –
Explosion Hazard - Batteries must only be changed in
non-hazardous locations
WARNING –
Explosion Hazard - Substitution of components may
impair suitability for use in hazardous locations
WARRANTY RETURN POLICY
Send all items for repair or replacement directly to Pelican Products
Customer Service Department (postage paid). Please call for a return
authorization number. Per our guarantee, Pelican Products will replace
or repair any broken or defective products. Upon receipt of goods,
Pelican Products will notify you of any handling and return postage
charges. If your local retailer does not stock the above accessory
parts, you may order them directly from Pelican Products. Send check
or money order in U.S. dollars, or order by phone using MasterCard
or VISA (ask for Customer Service). SORRY, NO C.O.D. ' s. Subject
to sales tax. Allow 2-3 weeks delivery time. Pelican Products pays
postage and handling charges.
PELICAN LEGENDARY LIFETIME
GUARANTEE OF EXCELLENCE
Pelican Products, Inc. guarantees its products for a lifetime
against breakage or defects in workmanship. This guarantee
does not cover the lamp or batteries (rechargeable or alkaline).
Any liability, either expressed or implied, is limited to replacement
of the product. This guarantee is void if the Pelican product has
been abused beyond normal and sensible use. This guarantee
does not cover shark bite, bear attack or damage caused by
children under five.
Lifetime Guarantee does not cover Roto Molded or AALG prod-
ucts. Refer to www.pelican.com/warranty for full details.
2000
CAUTION:
If light is not to be used for some time, remove batteries to prevent
CATALOG #2000
possible leakage and corrosion.
PRODUCT SPECIFICATIONS
Lamp Type:
Battery Type:
Battery Brand:
REPLACEMENT PARTS
2001
2004
Hydrogen Gas Absorber Pellets
Located inside the flashlight are catalyst pellets which are present
to absorb hydrogen gas that could possibly be emitted by defective,
leaking, reversed polarity or heavily discharged batteries. If the pellets
become wet, let them air dry. Pelican Products assumes no liability
for any brand batteries which are defective or cause injury to anyone
when used in any Pelican flashlight.
Battery Replacement
Battery replacement may only be performed in a non-hazardous area.
Do not mix battery brands or use Nicad or Zinc Carbon Batteries.
Do not mix old and new batteries. Replace all batteries at the
same time.
Lamp Replacement
Lamp replacement may only be performed in a non-hazardous area.
23215 Early Ave. • Torrance, CA 90505 USA
Tel (310) 326-4700 • FAX (310) 326-3311
Tel (+34) 93.467.4999 • FAX (+34) 93.487.7393 • www.peli.com
2003-311-000
All trademarks and logos displayed herein are registered and
unregistered trademarks of Pelican Products, Inc. and others.
Energizer and Energizer a registered trademarks
Xenon
E93 1.5V Alkaline C-cell (3)
Eveready Energizer
® ®
O-ring
Lamp Module
CAUTION: Read This Notice Before Use.
DO NOT MODIFY THIS PRODUCT!
www.pelican.com
PELICAN CANADA
TM
10221-184 St. • Edmonton, Alberta T5S 2J4
Tel (780) 481-6076 • FAX (780) 481-9586
PELI PRODUCTS, S.L.U.
TM
c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain
5-0758 Rev B ©2010 Pelican Products SP/10
of Eveready Battery Company, Inc.
SabreLite
TM
INSTRUCCIONES DE FUNCIONAMIENTO #CAT. 2000
INSTALACIÓN DE LAS PILAS
1. Retire el bastidor de la lente girándolo en sentido contrario
a las agujas del reloj.
2. Retire el módulo de la bombilla.
3. Retire la bandeja de pilas.
4. Retire las pilas usadas y coloque las pilas nuevas en la bandeja
teniendo en cuenta la polaridad como se muestra en la ilustración
impresa en la base de la bandeja.
5. Inserte la bandeja de pilas en la linterna con las dos piezas metálicas
apuntando hacia afuera.
6. Vuelva a colocar el módulo de la bombilla.
7. Vuelva a colocar el bastidor de la lente sobre la rosca y gire en el
sentido de las agujas del reloj al mismo tiempo que ejerce un poco
de presión sobre el mismo.
ENCENDIDO / APAGADO
La luz se enciende girando el bastidor de la lente en el sentido de las
agujas del reloj. Para apagarla, gire en sentido opuesto hasta que se
apague la luz. Siga girando aproximadamente una vuelta completa para
eliminar la posibilidad de que la luz se encienda por error al estar guar-
dada. NO APRIETE DEMASIADO.
REEMPLAZO DE LA BOMBILLA
Para cambiar el módulo de la bombilla, siga los pasos especificados para
la instalación de las pilas que aparecen a continuación:
Para retirar el módulo de la bombilla, siga los pasos No. 1 y 2.
Para cambiar el módulo de la bombilla, siga los pasos No. 6 y 7.
PELICAN
SabreLite
TM
OPERATING INSTRUCTIONS
CATALOG #2000
Submersible
23215 Early Ave. • Torrance, CA 90505
(310) 326-4700 • FAX (310) 326-3311
www.pelican.com
2000
TM
2000