Dust Extraction; Power Supply And Start-Up; Settings; Adjusting The Cutting Depth - Festool CMS-TS 75 Manual De Instrucciones Original

Slide the movable retainer [6-2] up to the stop

on the portable circular saw base.
Tighten the rotary knobs on both retainers [6-2]

+ [6-5].
The portable circular saw should now be securely
fixed to the retaining panel. Check this before con-
tinuing assembly.
6.4 Attaching the clip for the protective cov-
er mounting bracket [1-2]
Unscrew the locking knob [6-1] for the cutting

depth adjuster.
Press the portable circular saw downwards up

to the stop and tighten the locking knob [6-1].
Insert the clip for the protective cover mounting

bracket in the opening [7-1] for the protective

saw cover as shown in Fig. [7].
Push the spring [7-2] forwards and the clip

against the protective cover on the portable cir-
cular saw [7-3].
After releasing the spring [7-2] the clip must sit se-
curely in the opening for the protective cover. ln ad-
dition, the protective cover mounting bracket
should no longer press into the protective saw cov-
er. Check both before continuing assembly.
6.5 Installing the retaining panel in the basic
unit CMS-GE
Insert the retaining panel in the basic unit CMS-

GE the correct way round (see Fig. [8], Switch/
connector unit [8-1] on the left side). Grasp the
retaining panel by the recesses [8-2].
Close the two locks [8-3], clockwise).

6.6 Securing the protective cover [1-3]
Secure the protective cover by screwing the ro-

tary knob [9-1] into the hole on the protective
cover bracket [9-2].
6.7 Scale for cutting width [1-7]
Use the screws to secure the two rulers [10-1]

at the feed end of the basic unit.
Align the scales on the rulers so that the zero

points line up with the left and right cutting edg-
es of the saw blade.
6.8

Dust extraction

WARNING
Dust hazard
Dust can be hazardous to health. Always work

with a dust extractor.
Always read applicable national regulations be-

fore extracting hazardous dust.
The CS 70 AB extractor set is available as an acces-
sory and includes adapters for connecting the saw
unit to a Festool mobile dust extractor. The ex-
tractor set allows the user to simultaneously ex-
tract dust and chips both at the portable circular
saw (dia. 36 mm) and the protective cover (dia. 27
mm).
7

Power supply and start-up

WARNING
Unauthorised voltage or frequency!
Risk of accident
The mains voltage and the frequency of the pow-

er source must correspond with the specifica-
tions on the machine's name plate.
In North America, only Festool machines with

the voltage specifications 120 V/60 Hz may be
used.
The switch-/socket-unit [8-1] serves as voltage
supply and as ON-/OFF-switch of a power tool build
into the CMS-GE.
Insert the plug into an earthed socket.

Plug the electric power tool installed in the

CMS-GE into the connector .
You can now use the switch/connector unit to

switch the portable circular saw on and off (see
operating instructions for the CMS-GE).
8

Settings

WARNING
Risk of injury, electric shock
Always pull the mains plug out of the socket be-

fore performing any type of work on the ma-
chine!
 Change the portable circular saw settings (saw
blade changing system, saw tilt function, speed
adjustment switch) as shown in the operating
manual that accompanies your portable circular
saw.
8.1

Adjusting the cutting depth

Unscrew the rotary knob [11-2].

Move the saw up and down using the rotary

knob.
The indicator [11-1] shows the preset cutting
depth.
Tighten the rotary knob [11-2] at the required

cutting depth.
CMS-TS 75
GB
13