Device Configuration; Operations; Button Control; Sos - Cellularline GPS SAFE Manual De Instrucciones

S A F E G P S t r A c k E r

4. DEVICE CONFIGURATION

Device configurations must be completed prior to start-
ing tracking with your GPS SAFE.
To complete device configuration of your GPS SAFE,
please follow the instructions below:
1 . Launch Track Manager .
2. On Track Manager, click
on the main menu bar
to complete hardware settings.
4.1 Main
• Device Information: Fill in the device name and
phone number of your GPS SAFE, along with the PIN
Code required for your SIM Card .
• Device name, Phone number and Admin phone #1
entries are mandatory, and phone numbers must in-
clude country code and area code .
- Tracker Icon: Select the type of tracker your GPS
24
SAFE is .
• SOS Settings: Fill in at most 5 sets of phone numbers
for SOS alerts.
The entry of Admin phone #1 is mandatory, for it is the
SOS phone number that GPS SAFE will call out to in
case of emergency .
• Select Profile: Select a profile from the listed 5 op-
tions .
- Volume: Adjust the volume of the audio receiver
or speaker .
Note: Please be cautious and do not press close against
the speaker in loud speaker mode to avoid possible hear-
ing damage.
- Emergency SMS Report: Select the event that you
want to receive an emergency report for via SMS,
such as SOS event, Free-fall event, Geofence
event, Unexpected movement event, and Bat-
tery-low event.
- Report tracking data via:
- no report (recommended)
- report via SMS
- report via GPRS is DISABLED
- Tracking Interval: Select the tracking interval for
your GPS SAFE .
- Report Interval: Select the interval for your GPS
SAFE to send a tracking report .
- Free-fall detection: This option alerts the owner
when the device falls down from somewhere with
great altitude. Cases like this include working at a
spot with great heights, mountain climbing or hik-
ing and etc .
- Reset: Click to reset hardware settings back to de-
faults .
4.2 Geofence
Click to set the geofence area by dragging and
moving the frame shown on the map.
• Enable Geofence Alert: Click to start receiving geo-
fence alerts .
- Alert Type: Select whether you want to receive the
geofence alert when the device enters the geofence
area, exits the geofence area or both .
- Geofence Area: Here lists the measurement details of
the geofence area .
• Disable Geofence Alert: Click to stop receiving geo-
fence alerts .
S A F E G P S t r A c k E r

5. OPERATIONS

5.1 Button control

Button Operation Outcome
Press down the Power Turns ON or OFF the GPS
Power
button for 2 seconds . SAFE .
1 . Activates quick-dial to
the Admin phone .
Press down the Call 2. Answers a call when the

Call

button for 2 seconds . GPS SAFE rings .
3. Hangs up a call after it is
answered.
Activates the SOS alert.
The SOS alert can be
Press down the SOS-

SOS

de-activated by pressing
button for 2 seconds .
either the Call or Power
button .
1 . R emove the battery .
2. Press down both
Call + Power buttons
simultaneously,
Call + Resets the device back to
andthen insert the
Power factory defaults .
battery back in. Do
not let go of the
buttons before the
battery is inserted .
5.2 SOS
SOS function
To send out a SOS alert:
1. Press down the SOS button for 2 seconds to activate
SOS alarm.
2 . When it is activated, the GREEN/RED power LEDs and
BLUE GPS LED will stay on.
3. The device will then start an alerting/warning sound.
4. GPS will start getting a fix of where you are.
5. SOS alerts will be submitted to all the SOS phone
numbers that are previously defined before a GPS fix
IT
EN
FR
ES
DE