Tabla de contenido
Publicidad
BEFORE USE, BE SURE THE SYSTEM IS AT STOP MODE BEFORE PROGRAMMING:
1. PRESS FUNCTON BUTTON TO "CD" AND AT STOP MODE
2.PRESS THE MODE BUTTON, "MEM" WILL BE FLASHING ON LCD DISPLAY. MOREOVER, IT WILL INDICATE
PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED.
3.SELECT A DESIRED TRACK BY TURNING
DISC,
PRESSING ALBUM DOWN OR ALBUM UP TO SEARCH FOLDER BACKWARD OR FORWARD.
4.PRESS THE MODE BUTTON TO STORE THE TRACK INTO MEMORY.
5.REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.
6.WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS PLAY/PAUSE
PLAY THE TRACKS IN ASSIGNED ORDER.
BUTTON
7. PRESS STOP
AGAIN TO
CANCEL PROGRAMMING.
COPYING OF CD
THE SYSTEM ALLOWS YOU TO COPY THE TRACK FROM CD TO USB OR SD BY 1 TRACK, 1 FOLDER OR ALL
FILES.
I) COPY 1 TRACK
1.INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, PRESS CD/USB/SD BUTTON TO "CD" MODE.
REC
2.PRESS
BUTTON DURING THE PLAYBACK OF THE COPYING TRACK FROM CD, THEN "ONE" WILL BE
FLASHING ON THE DISPLAY. PRESS
3.THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY. COPYING IS PERFORMING NOW.
4.AFTER COMPLETING OF COPY, UNIT WILL STOP PLAYBACK AUTOMATICALLY.
5.DISPLAY WILL SHOW "END" AND BACK TO CD MODE.
II) COPY 1 FOLDER (FOR MP3/WMA DISC ONLY)
1.INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, SET IN CD & STOP MODE AFTER UNIT READING.
2. PRESS ALBUM DOWN OR ALBUM UP TO SEARCH FOLDER FOR COPYING.
3. PRESS REC BUTTON, THEN "ONE" WILL BE FLASHING ON THE DISPLAY. TURN SKIP UP
BUTTON TO SELECT "DIR" ON THE DISPLAY. PRESS
4. USB OR SD ICON WILL BE FLASHING ON THE DISPLAY. COPYING IS PERFORMING NOW.
5. WHEN THE USB OR SD ICON STOPS FLASHING, IT MEANS THAT THE FOLDER COPYING IS COMPLETED.
III) COPY ALL TRACK
1.INSERT THE USB STORAGE MEDIA OR SD/MMC CARD, PRESS FUNCTON BUTTON TO "CD" MODE.
2. PRESS REC BUTTON, THEN "ONE" WLL BE FLASHING ON THE DISPLAY. PRESS SKIP UP
KNOB TO SELECT "ALL" ON THE DISPLAY. PRESS
4. USB OR SD ICON WILL BE FLASHING ON THE DISPLAY. COPYING IS PERFORMING NOW.
5. WHEN THE USB OR SD ICON STOPS FLASHING, IT MEANS THAT ALL TRACK COPYING IS COMPLETED.
SPLIT TRACK FUNCTION FOR USB/SD RECORDING FOR TURNTABLE/AUX IN
1)
MANUAL SPLIT OPERATION PROCEDURE: DURING USB/SD RECORDING, THE USB/SD ICON WILL
FLASH ON THE DISPLAY. IF A NEW TRACK IS REQUIRED, PRESS MODE BUTTON ON THE UNIT OR REMOTE
CONTROL, DISPLAY WILL SHOW "TS", THEN THE UNIT WILL STOP RECORDING MOMENTARILY AND RESUME
AGAIN. A NEW FILE WILL HAVE BEEN CREATED ON THE USB/SD DEVICE REPRESNTING A NEW TRACK.
2)
AUTO SPLIT OPERATION PROCEDURE:
-
BEFORE USB/SD RECORDING, SELECT AUDIO SOURCE, THEN PRESS MODE BUTTON ON THE UNIT
OR REMOTE CONTROL, DISPLAY WILL SHOW "T-ON", WHICH MEANS THE AUTO SPLIT FUNCTION HAS
ACTIVATED. THEN START USB/SD RECORDING, THE UNIT CAN AUTOMATICALLY DETECT THE SILENT PART
BETWEEN EACH TRACK, AND CREATE A NEW FILE TO MOVE ON TO START RECORDING THE NEXT TRACK.
-
IF NOT REQUIRED: PRESS MODE BUTTON ON THE UNIT OR REMOTE CONTROL BEFORE USB/SD
RECORDING, DISPLAY WILL SHOW "T-OF", WHICH MEANS AUTO SPLIT HAS BEEN DEACTIVATED.
-
PLEASE NOTE FOR AUTO SPLIT: SEVERAL SECONDS OF THE BEGINNING OF THE NEXT TRACK MAY
NOT BE RECORDED, AS THE UNIT MAY TAKE A FEW SECONDS TO CREATE A NEW FILE ON THE USB/SD; AND
IT CAN ADDITIONALLY BE THE CASE THAT SOME MUSIC PRODUCERS INTENTIONALLY ADD SILENT
SECTIONS WITHIN ONE TRACK. AS A RESULT, THIS WILL VERY LIKELY MAKE THE UNIT CONSIDER THIS
SILENT PART THE BREAK BETWEEN TRACKS AND CREATE A NEW TRACK ON THE RECORDING.
-
NOTE FOR AUTO SPLIT: DURING USB/SD RECORDING FROM TURNTABLE, WHEN THE UNIT HAS
DETECTED ANY PARTICULAR SILENT PART, THE TURNTABLE WILL STOP MOMENTARILY. THE TURNTABLE
WILL RESUME OPERATION ONCE THE USB/SD DEVICE HAS BEGUN CREATING A NEW FILE TO BE
RECORDED.
SKIP UP
TO STOP PLAYING OF PROGRAMMED TRACKES, PRESS STOP
REC
BUTTON AGAIN TO CONFIRM.
OR SKIP DOWN
REC
BUTTON AGAIN TO CONFIRM.
REC
BUTTON AGAIN TO CONFIRM.
9
KNOB. FOR MP3/WMA
BUTTON
BUTTON
/ SKIP DOWN
/ SKIP DOWN
TO
Publicidad
Tabla de contenido
