Product Information - Night Stick TAC-460XL-K01 Manual De Instrucciones

The TAC-460XL tactical fl ashlight comes with the tail cap switch already
attached. As such, the light can be used right out of the packaging as a
conventional tactical fl ashlight once the included CR-123 batteries and CR-
123 Battery Carrier are installed. This light may be converted back to this
confi guration at any time.
STEPS NECESSARY TO ASSEMBLE THE NIGHTSTICK XTREME
LUMENS TACTICAL LONG GUN KIT
1. Remove the Tail Cap Switch (Figure 1-A) and the CR-123 Battery Carrier
(Figure 1-B). NOTE: Keep the Tail Cap Switch for future use if this light is to
ever be converted back to a conventional Tactical Flashlight.
2. Install the two included CR-123 Batteries (Figure 2-A) into the CR-123
Battery Carrier (Figure 2-B). The positive terminals on each battery should
be oriented in the direction of the arrow on the CR-123 Battery Carrier and
then inserted into the fl ashlight with the + end terminals pointing in the
direction of the fl ashlight's bezel (Figure 3-A).
3. Install the Remote Pressure Switch (Figure 3-B) and tighten into place.
4. Test the operation of the Remote Pressure Switch (Figure 3-C) and
the Side Switch (Figure 3-D).
Momentary On/Off operation of the light only. The Side Switch provides
Momentary On/Off operation by pressing slightly on the button, or Constant-
on by pressing until the button clicks.
5. Decide where the Quad Lock Mount (Figure 4-A) is to be located on the
light. It is important that the mount remain clear of the Remote Pressure
Switch, otherwise accessing the batteries and CR-123 Battery Carrier will
require complete disassembly of the Quad Lock Mount.
6. Once the appropriate location of the Quad Lock Mount along the handle
of the light has been determined, remove all 4 of the Cap Head Screws
(Figure 5-A) using the supplied Allen Wrench (Figure 5-B).
7. While holding the lower half of the Quad Lock Mount (Figure 5-C) in
place on the light, press each of the top rails (Figure 5-D) in to alignment
with the lower half and start all 4 of the Cap Head Screws (Figure 5-A).
IMPORTANT: Get all 4 of the Cap Head Screws partially installed before
tightening.
8. Begin tightening all 4 Cap Head Screws (Figure 6-A) by alternating back
and forth and tightening a little at a time. When all 4 are tightened into
place (DO NOT over-tighten), the gap between the lower half of the mount
and the two top rails should be approximately 1/16" and should be equal
on both sides.
9. Test fi t the Quad Lock Mount on to the mil spec Picatinny or Weaver
rail of the long gun (Figure 9-A). At the same time, determine the desired
location of the Remote Pressure Switch (Figure 9-B). NOTE: The Remote
Pressure Switch may be attached to any clean, dry fl at surface on the long
gun. The location indicated in Figure 9 is just one possibility. The actual
location on your long gun will be determined by your weapon's confi guration
and by your preferences.
10. Once the location of the Quad Lock Mount (Figure 9-A) and the Remote
Pressure Switch (Figure 9-B) have been determined, clean the location on
your weapon where the Remote Pressure Switch will be located as well as
the inside surface of the Remote Pressure Switch (Figure 7-A) using the
supplied Alcohol Swab (Figure 7-B).
11. Peel back one of the paper backings on the included Velcro Pressure
Sensitive Adhesive Strip (Figure 8-A) and press it into place on the back
side of the Remote Pressure Switch (Figure 8-B).
12. Attach the Quad Lock Mount with the light installed onto the mil spec
Picatinny or Weave rail of your weapon (Figure 9-A)
13. Peel back the paper backing on the Velcro Pressure Sensitive Adhesive
Strip and press it into place on the previously cleaned area on your long
gun (Figure 9-B).
14. NOTE: The Pressure Sensitive Adhesive will set up and make a semi-
permanent bond after about 24 hours, so please do not move/remove
the Pressure Sensitive Adhesive Strips once they have been placed.
Additionally, do not attempt to separate the two Velcro sections until after
that time.
OPERATION
The Nightstick Xtreme Lumens Tactical Long Gun Kit is now fully
installed and ready for use.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mynightstick.com
The Remote Pressure Switch provides
The Remote Pressure Switch provides Momentary On/Off operation of
the light only. Using this switch, gives the operator full and instant control
over when the light is on, and when it is off
The Side Switch provides Momentary On/Off operation by pressing
slightly on the button, or Constant-on by pressing until the button clicks.
If the Quad Lock Mount has been positioned correctly (see Step 5
above), changing the batteries may be accomplished without removing
the light from the Quad Lock Mount, and depending on your installation
location, it may be possible to change the batteries without removing the
mount from your weapon.
To change the batteries, fi rst separate the two halves of the Velcro Strip
from each other so that one half stays adhered to your weapon and the
other remains attached to the back side of the Remote Pressure Switch.
Next unscrew the Remote Pressure Switch, remove the CR-123 Battery
Carrier and replace the batteries (see Step 2 above).
BAYCO PRODUCTS LIMITED LIFETIME WARRANTY
WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in
workmanship and materials for the original purchaser's lifetime. The Limited
Lifetime Warranty includes the LEDs, housing and lenses. Rechargeable
batteries, chargers, switches, electronics and included accessories are
warranted for a period of two years with proof of purchase. Disposable, non-
rechargeable batteries are excluded from this warranty. Normal wear and
failures which are caused by accidents, misuse, abuse, faulty installation
and lightning damage are also excluded.
In the event that Bayco Products, Inc. receives notice that any product
does not conform to its warranty, the original purchaser's sole and exclusive
remedy, and Bayco Products, Inc.'s sole and exclusive liability, shall be
for Bayco Products, Inc., at its sole option, to either repair or replace the
non-conforming product in accordance with this limited warranty. The
original purchaser shall follow the instructions below to qualify for a repair
or replacement product. This is the only warranty, expressed or implied,
including any warranty of merchantability or fi tness for a particular purpose.
IN NO EVENT WILL BAYCO PRODUCTS, INC. OR ITS AFFILIATES
OR SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS OF
THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE.
CUMULATIVE LIABILITY TO CUSTOMER, FROM ALL CAUSES OF
ACTION AND ALL THEORIES OF LIABILITY, WILL BE LIMITED TO AND
WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT PAID
BY CUSTOMER.
If this product is used for rental purposes, the warranty term is reduced
to 90 days from the date of purchase.
WARRANTY CLAIMS – USA
Return the product to the place of purchase for all warranty related
issues. If this is not possible, contact Bayco Customer Service at (800) 233-
2155 M-F 8-5 Central Time for a Return Goods Authorization (RGA). Do not
return this product to Bayco without fi rst receiving an RGA Number from
Bayco Customer Service. When returning the product, the RGA Number
must be written on the outside of the shipping box.
WARRANTY CLAIMS – OUTSIDE OF USA
Return the product to the place where purchased for all warranty related
issues.
EXTENT OF COVERED WARRANTY WORK
Bayco will repair or replace this product at our option. If it is determined
that the warranty is no longer in effect, Bayco will contact you with a repair
estimate before beginning any work.
WARRANTY QUESTIONS
If you have any questions about this warranty or any other Bayco
product inquiries, please contact Bayco Customer Service at (800) 233-
2155 M-F 8-5 Central Time.

PRODUCT INFORMATION

Date of Purchase __________________________________________
INS-T460XL-K01-15
THE TOTAL