Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Z
GSM signal quality
Function
Displaying GSM signal quality
SMS Syntax
<pin><command>
<pin>
0000 (Default)
<value>
'range from...to'
SMS syntax example
0000Z
SMS reply example
Signal level: 12
Automatic reply SMS
Yes
NOTE. The command 'Z' analyses the quality of the GSM signal, and returns a
numerical value to the user: 0-1 (minimum), 17-23 (average), 31 (maximum)
*
Relay 1 activation
Function
Relay 1 activation via sms
SMS Syntax
<pin><command>
<pin>
0000 (Default)
<command>
*
<value>
0, 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example
0000*
SMS reply example
Relay 1 activation
Automatic reply SMS
Yes
NOTE. Activating relay 1 can also be carried out during an active call by press-
ing the * button on your phone keypad.
#
Relay 2 activation
Function
Relay 2 activation via sms
SMS Syntax
<pin><command>
<pin>
0000 (Default)
<command>
#
<value>
0, 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example
0000#
SMS reply example
Relay 2 activation
Automatic reply SMS
Yes
NOTE. Activating relay 2 can also be carried out during an active call by press-
ing the # button on your phone keypad.
**
Relay 1 closure time
Function
Setting and/or modifying relay 1 closure time
SMS Syntax
<pin><command><value>
<pin>
0000 (Default)
<command>
**
<value>
0 (disabled), 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example
0000**5
SMS reply example
Relay closure time: 5
Automatic reply SMS
Yes
Default
3
NOTE. The value is expressed in seconds
14
##
Relay 2 closure time
Function
Setting and/or modifying relay 2 closure time
SMS Syntax
<pin><command><value>
<pin>
0000 (Default)
<command>
##
<value>
0 (disabled), 1, 2, 3, 4, 5, 6, 7, 8, 9
SMS syntax example
0000##5
SMS reply example
Relay closure time: 5
Automatic reply SMS
Yes
Default
3
NOTE. The value is expressed in seconds
Commands during conversation
Increase
speaker
1
volume
Reduce
4
speaker volume
7
*
Relay 1 activation
Ending the call *
The call is ended by pushing button '0' only on telephones on fixed networks.
Speaker Volume
If during the call the person you are talking to cannot hear your voice at the
right volume, you can increase the speaker volume by pressing key 1, or lower
it by pressing key 4.
Microphone Sensitivity
If you can't hear the voice of the person in front of the audio entry panel, you
can press key 3 to increase or key 6 to reduce the sensitivity of the microphone.
Relay activation
Via the two relays, you can control the opening of a front door or automated
gate. This operation can be carried out during a call by pressing the
to activate the first relay, or pressing the
NOTE: both relays cannot support voltages above 60V and currents with a
load over 500mA.
Ending the call
This function must be used when your GSM audio receiver device contacts a
number on a fixed line. By pressing key '0' you will stop the call.
NOTE: If button '0' is not pressed, the call will remain on the line until the audio
receiver's TIMEOUT time ( See parameter 'H' ).
Increase
2
3
phone sensitivity
Reduce microphone
5
6
sensitivity
8
9
#
0
Relay 2 activation
button to activate the second relay.
micro-
button
Publicidad
Tabla de contenido
