Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Before unloading or making adjustments.
When maintaining the tool.
When clearing a jam.
When touching the safety yoke.
When tool is not in use.
When moving to a different work area.
Such precautionary measures reduce the risk of
injury to persons.
LOADING TOOL
●
Do not load the tool with fasteners when
any one of the operating controls is
activated.
●
Never place a hand or any part of body in
fastener discharge area of tool.
●
Never point tool at anyone.
●
Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
WARNING:
!
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
UNPACKING
This tool has been shipped completely
●
assembled.
●
Make sure that all items listed in the packing
list are included.
Carefully remove the tool and any
●
accessories from the box.
Inspect the tool carefully to make sure no
●
breakage or damage occurred during
shipping.
●
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
●
If any parts are damaged or missing, please
call
1-866-676-8468
.
WARNING:
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
06
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
FEATURES
SPECIFICATIONS
REQUIRES:
3.8 SCFM with 100
fasteners per minute @ 90 psi
AIR INLET:
1/4 inch NPT
MAGAZINE CAPACITY:
100 fasteners
WEIGHT:
1.7 lbs
MAXIMUM PRESSURE:
100 psi
–
PRESSURE RANGE:
60 psi 100 psi
PIN SIZE RANGE: 1/4 inch to 9/16 inch
Compatible with All Generic Fine Wire Staples.
FEATURES
●
360° ADJUSTABLE EXHAUST
Allows user to direct air away from face.
COMFORT-GRIP HANDLE
●
For increased comfort and control.
●
ERGONOMICALLY ENGINEERED BODY
Rugged and Comfortable debris free, extending
tool life.
●
NON-MARRING SAFETY CONTACT
Eliminates damage to working surface.
OPERATION
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool allows
users to direct the exhaust according to operator
preference. To adjust the direction, turn the exhaust
cap in the desired direction.
LOADING FASTENERS
⒈
Connect the tool to the air resource.
⒉
Push down on the latch button(B). Pull back on
the inner magazine (C).
Please load the fasteners with the head of the
⒊
staples facing the same direction as the work
contact element beneath the magazine.
tool is a bottom loading stapler!
⒋
Push the inner magazine(C) forward until latch
button pops up.
Latch button(B)
Inner Magazine (C)
WARNING:
!
The tool may fire when it is first
connected to the air resource. Always
connect the tool to the air resource
before loading fasteners to prevent injury
from unintended cycling. Always make
sure the tool's magazine is empty at the
beginning of each work session, before
connecting to an air resource.
WARNING:
!
Use only those fasteners recommended
for use with this tool. Fasteners not
identified for use with this tool by the tool
manufacturer are able to result in a risk of
injury to persons or tool damage when
used in this tool.
WARNING:
!
Keep the tool pointed away from yourself
and others when loading fasteners.
Failure to do so could result in possible
serious personal injury.
WARNING:
!
Never load fasteners with the workpiece
contact or trigger activated. Doing so
could result in possible serious personal
injury.
UNLOADING FASTENERS
This
Unloading is the reverse of loading. Always
disconnect the air resource before unloading.
WARNING:
!
Always unload all fasteners before removing
tool from service.
WARNING:
!
Always disconnect the air resource before
unloading.
CLEARING JAMS
Occasionally, a fastener may become jammed in
the firing mechanism of the tool, making the tool
inoperable. To remove a jammed fastener, follow
the steps below:
1.
Disconnect the tool from air resource.
2.
Remove fasteners from the tool. Failure to do
so will cause the fasteners to eject from the front
of the tool.
⒊
Completely remove the small nose screws (E)
and the top nose plate (F) to reveal the jammed
fastener.
⒋
Using caution not to bend or damage the driver
blade, using pliers or a screwdriver if required to
clear the jammed fastener.
⒌
Put the nose plate (F) back on the nose (G),
fastening it with the screws (E).
⒍
Reconnect the tool to the air resource.
⒎
Reload the tool with fasteners.
07
Publicidad
Tabla de contenido
