Tabla de contenido
Publicidad
EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
PRODUCT FEATURES
The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Thumbwheel for orbit frequency preselection
2 On/Off switch
3 Battery charge-control indicator
4 Battery pack*
5 Dust box assembly
6 Sanding plate
7 Auxiliary handle (insulated gripping surface)
8 Battery unlocking button*
9 Handle (insulated gripping surface)
10 Sanding sheet*
11 Dust box (Alignment aid for sanding sheet)
12 Screws for sanding plate
13 Sanding-plate base
14 Extraction outlet
15 Vacuum hose*
16 Screw for auxiliary handle
17 Wing nut
18 Cap of dust box
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our accessories
program.
TECHNICAL DATA
Product mame
24V Cordless Random orbit sander
Rated voltage
24V
No-load speed
3000–12000 min-1
No-load orbital
6000–24000 min-1
stroke rate
Orbit diameter
3.2 mm
Sanding plate
125 mm
diameter
Weight (without
battery and
1.41 kg
charger)
Battery
29807 / 29837
2913907(VDE & BS) /
Charger
29817(VDE) / 29827(BS)
NOISE/VIBRATION INFORMATION
Sound emission values determined according to EN
60745-2-4.
Typically the A-weighted sound pressure level of the
English (Original Instructions)
product is 77 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
K determined according to EN 60745-2-4: a
2
K=1.5m/s
.
The vibration level given in this information sheet has
been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool
with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
insertion tools or is poorly maintained, the vibration
emission may differ. This may significantly increase the
exposure level over the total working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job.
This may significantly reduce the exposure level over the
total working period. Identify additional safety measures
to protect the operator from the effects of vibration such
as: maintain the tool and the accessories, keep the hands
warm, organisation of work patterns.
ASSEMBLY
Battery Charging
■ Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery
of your power tool.
Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time.
The lithium-ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithium-ion battery is protected against deep
discharging by the "Electronic Cell Protection (ECP)".
When the battery is empty, the machine is switched off by
means of a protective circuit: The inserted tool no longer
rotates.
■ Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
Observe the notes for disposal.
Removing the battery (see figure A)
To remove the battery 4, press the battery unlocking
button 8 and pull the battery out of the power tool toward
the rear. Do not exert any force.
2
(triax vector sum) and uncertainty
h
=4.5m/s
h
2
,
Publicidad
Tabla de contenido
