Maintenance/Service - wolfcraft EG 300 Instrucciones De Aplicación

Applying the sealant
• Make sure the working area is clean and dry (remove old sealant, where applicable).
• Hold the tool in a slightly inclined position and move it, with the trigger C being pressed, carefully and at an even speed
along the gap or crack to be filled.
• Make sure that the sealant gets in full contact with both surfaces that are to be sealed.
• In order to stop the flow of sealant, just release the trigger C. The automatic drip-stop function will prevent more
material from being pressed out of the cartridge thereafter.
• The tool will automatically switch into the power-saving mode after a few minutes. This can be seen from the LED light
which goes out.
• Smooth down the sealant with a suitable tool and remove any superfluous material.
• Remove all possible material residues at the cartridge nozzle and at the caulking gun without any delay.
Electronic overload protection
• It will stop the motor automatically, if too much pressure is exerted on the cartridge, and thus prevent any damage
to the tool and to the cartridge.
• In order to avoid any overload, you should always ensure that
- solidified material (residues) is removed from the nozzle (use a new nozzle tip, if necessary),
- the cartridge is neither damaged nor frozen,
- the cartridge compartment is free from sealant.
Changing a cartridge
• Before removing an empty cartridge, move the piston plunger completely back.
• In order to do so, press the multi-functional switch G backward into the „Return" position (Fig. 8). Then release
the automatic return function of the piston plunger by briefly pressing the trigger C. This action will take approx. 2 min,
during which time you can switch off the caulking gun and prepare the next cartridge for being inserted.
• Now remove the empty cartridge by pressing both release levers of the locking mechanism for the cartridge at the
same time. Pull out the cartridge from the caulking gun with your other hand (Fig. 5).
• Insert the next cartridge as described in the section „Inserting a cartridge" above (Fig. 4).
After finishing work
• After you have finished work, put the multi-functional switch G in its „Neutral" position (Fig. 9). The LED light will go
out immediately.
• Also put the multi-functional switch G in its „Neutral" position (Fig. 9), if you intend to take the caulking gun
somewhere else.
• Always separate the cartridge from the caulking gun, when the latter needs to be transported or stored.
In such case, move the piston plunger B completely back.

MAINTENANCE/SERVICE

• Always keep your tool clean.
• Have your electric tools repaired by a suitably qualified electrician only and use exclu-sively original spares.
This will ensure the safety of your electric tools. Please contact our Service Hotline for this purpose.
• Keep all safety and other instructions for future reference.
ENVIRONMENT
• Do not dispose of electric tools, accessories and packaging material in the household refuse (EU countries only).
• In accordance with the European Directive 2002/96/EC on waste electrical and electronic equipment (WEEE) and
its implementation into national law, disused electric tools must be collected separately and recycled in an
environmentally-friendly way.
• Non-rechargeable and rechargeable batteries must be properly disposed of and must not be disposed of in the
household refuse.
WARRANTY
Dear do-it-yourselfer, we grant a 5-year warranty on the wolfcraft
during this warranty period that must be attributed to faulty materials, wolfcraft
The warranty period shall commence on the date, when the product has been purchased, so do keep the invoice or the
purchase receipt. Prerequisites for honouring this warranty promise is that you use the tool you have purchased under
this warranty exclusively for private, i.e. not commercial purposes and that you use original wolfcraft
Defects resulting from the usual wear and tear, from improper use or insufficient maintenance, any other signs of wear
and faults of which the customer was aware at the time of purchasing the equipment shall be excluded from the warranty.
The warranty shall become void, should the customer open the equipment or has it opened. Warranty claims can only
be asserted by producing the original purchase receipt.
t
® product you have purchased. Should any defect occur
shall replace the product free of charge.
®
10
® spares only.