Smeg Set160X Instrucciones Para El Uso página 2

English
WARNING
--------------------------------------------------
The distance between the hob and the lower
part of the hood must be at least 65 cm.
The air collected must not be conveyed into
a duct used to blow off smokes from ap-
pliances fed with an energy other than
electricity (central heating systems, ther-
mosiphons, water-heaters, etc.).
Comply with the official instructions provided
by the competent authorities in merit when
installing the disposal duct.
The room must be well aerated in case a
hood and some other heat equipment fed
with an energy other than electricity (gas,
oil, coal heaters, etc) operate at the same
time.
In fact the intake hood, disposing of air, could
create a vacuum in the room. The vacuum
should not exceed 0,04mbar. This prevents
the gas exhausted by the heat source from
being intaken again. It is therefore advisable
to ensure the room contains air taps able to
ensure a steady flow of fresh air.
ATTENTION: This appliance must be
grounded.
The following warning is valid in the United
Kingdom only:
As the colours of the wires in the mains lead
of this appliance may not correspond with
the coloured markings identifying the
terminals in your plug, proceed as follows:
– the wire which is coloured green and
yellow must be connected to the terminal
in the plug which is marked with the letter
E or by the earth symbol [ ], or co-
loured green or green and yellow;
– the wire which is coloured blue must be
connected to the terminal which is marked
with the letter N or coloured black;
– the wire which is coloured brown must be
connected to the terminal which is marked
with the letter L or coloured red.
When making the electrical connections,
check that the current socket has a ground
connection and that the voltage values
correspond to those indicated on the data
plate inside the appliance itself.
In case your appliance is not furnished with
a non separating flexible cable and has no
plug, or has not got any other device ensu-
ring omnipolar disconnection from the elec-
tricity main, with a contact opening distance
of at least 3 mm, such separating device
ensuring disconnection from the main must
be included in the fixed installation.
Always switch off the electricity supply be-
fore carrying out any cleaning or servicing
operations on the appliance.
USE
--------------------------------------------------
Avoid using materials which could cause
spurts of flame (flambées) near the ap-
pliance.
When frying, take particular care to prevent
oil and grease from catching fire. Already
used oil is especially dangerous in this re-
spect. Do not use uncovered electric grates.
To avoid possible risks of fire always comply
with the indicated instructions when cleaning
anti-grease filters and when removing grease
deposits from the appliance.
MAINTENANCE
--------------------------------------------------
Thorough servicing guarantees correct and
long-lasting operation.
Particular care must be paid to the grease
filtering panels which must be periodically
cleaned in relation to use (at least once every
two months). Remove the grease filters and
wash them either by hand or in the
dishwasher using neutral detergent.
Use lukewarm water and neutral detergent
to clean painted appliances. Never use
products containing abrasives.
Take great care to prevent the use of corro-
sive or abrasive products when cleaning
steel, copper or brass appliances. It is advi-
sable to use specialized products according
to the manufacturer's instructions.
DESCRIPTION
---------------------------------------------------
The equipment can be used for external evacu-
ation, suction, or for internal recycling of air,
filtering.
When the Filtering version is in use, the air
and fumes cleaned by the active charcoalfilter
are recirculated in the room (Fig. 1).
When the Ducting version is in use the fumes
are conveyed upwards through a flue pipe and
evacuated directly towards the outside (Fig. 2).
The charcoalfilters are no more necessary.
INSTALLATION
---------------------------------------------------
To fit apparatus into cupboard: (Fig. 3)
Fit the apparatus to the cupboard using the
screws supplied.
Screws "B" serve to hook up the apparatus to
the bottom of the cupboard. Insert these screws
working from the bottom of the visor after open-
ing it fully.
Also the hood must be fixed to the wall unit
using the lateral brackets. Fix the brackets to
the hood using the screws marked D provided,
and using the appropriate slotted plates which
allow the width from the brackets to the side of
the wall unit to be adjusted between 20 and 16
mm (Fig. 4). The brackets are hooked onto the
wall unit using the appropriate screws marked
C (Fig. 3).
To cover any possible gap between back of
hood and wall, the spacers provided should be
positioned appropriately (Fig. 5-6-7).
For any substitution of the front-block on
visor operate as follow (Fig. 8):
– Slide the visor until completely open.
– To gain access to the front-block screws,
disconnect the switch-board metal protec-
tion 1 by unscrewing screws B.
– Disconnect the front-block 2 by screws C.
– Once the new front-block is in place reinsert
the switch-board metal protection.
OPERATION
(Fig. 9)
---------------------------------------------------
"A" - Fan on selector switch. In position 1 the
motor is automatically switched on when
the telescopic visor is opened. In position
0 the motor is always off.
"B" - Motor operating speed selector switch
operating via an electronic speed variator.
"C" - Light on selector switch; in the AUT
position the light will automatically be
switched on and off when the telescopic
visor is opened/closed.
When position 0 is selected the light re-
mains off, regardless of the visor position.
When switched to MAN, the light can be
switched on regardless of the visor
position.
Special care should be given to the anti-grease
filtering panels which should be periodically
cleaned according to use (every two months at
the most) by washing it in luke-warm water
either by hand or in a dishwashing machine, at
a temperature of 60°.
To remove the two grease-trap panels (Fig. 10),
move the stays to the inside and rotate the
filter panel downwards until it is completely
released from its seating.
To replace the two filters, repeat the operation
in reverse order.
If the filter version of the hood is used, the
activated carbon filters will need to be
replaced every 6 months. To remove the filters,
proceed as follows: (Fig. 11)
Fully open telescopic visor and remove grease-
trap panels as described.
The filters will then be accessible; grip filter
and rotate clockwise to release the bayonet
hole of each filter from the stay pins.
Remove the other support from the connection
housing and remove filters.
To replace new filters, repeat the operation in
reverse order.
To obtain access to the lighting lamp, remove
the light fitting by unscrewing fixing screws
(Fig. 12). Replace with lamps of the same type.