Publicidad
Idiomas disponibles
Idiomas disponibles
peak must remain in the maximum open position previously reached - higher than the "0" position - and thereafter must be
automatically shifted downwards along with the visor - positioning itself and remaining stable in the "0" position.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please refer to a Nolan authorized dealer.
VISOR
5
Visor Disassembly
To disassemble the visor first remove the lateral latches and (if assembled) the peak - see instructions above.
5.1
Open the visor completely (Fig. 7).
5.2
Push the release lever of the left side mechanism completely upwards moving it over the side trim (Fig. 8) and pull the visor
away from the helmet (Fig. 9).
5.3
Release the release lever and replace it downwards in its original position moving it over side trim.
5.4
Follow the same steps on the right side of the helmet.
6
Visor Assembly
6.1
Place the left side of the visor on the corresponding side mechanism centring the side hole of the visor on the mechanism itself
(Fig. 9).
6.2
Push the release lever of the mechanism completely upwards moving it over the side trim and press the visor against the side
mechanism (Fig. 8, 9).
6.3
Disengage the release lever and replace it downwards in its original position moving it over the side trim. Then check that the
visor remains attached to the mechanism by pulling it outwards.
6.4
Follow the same steps on the right side of the helmet.
6.5
If desired, replace the peak above the visor, and finally always replace both lateral latches (see instructions above).
6.6
Close the visor completely.
WARNING
-
Make sure that the mechanisms are working properly. Open and close the visor making sure that the mechanisms hold it in
the different positions.
-
If necessary, repeat the above-mentioned steps.
-
If the peak is assembled over the visor check the proper functioning as described previously.
-
Do not use the helmet if the visor and the lateral latches have not been assembled properly.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please refer to a Nolan authorized dealer.
peak must remain in the maximum open position previously reached - higher than the "0" position - and thereafter must be
automatically shifted downwards along with the visor - positioning itself and remaining stable in the "0" position.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please refer to a Nolan authorized dealer.
VISOR
5
Visor Disassembly
To disassemble the visor first remove the lateral latches and (if assembled) the peak - see instructions above.
5.1
Open the visor completely (Fig. 7).
5.2
Push the release lever of the left side mechanism completely upwards moving it over the side trim (Fig. 8) and pull the visor
away from the helmet (Fig. 9).
5.3
Release the release lever and replace it downwards in its original position moving it over side trim.
5.4
Follow the same steps on the right side of the helmet.
6
Visor Assembly
6.1
Place the left side of the visor on the corresponding side mechanism centring the side hole of the visor on the mechanism itself
(Fig. 9).
6.2
Push the release lever of the mechanism completely upwards moving it over the side trim and press the visor against the side
mechanism (Fig. 8, 9).
6.3
Disengage the release lever and replace it downwards in its original position moving it over the side trim. Then check that the
visor remains attached to the mechanism by pulling it outwards.
6.4
Follow the same steps on the right side of the helmet.
6.5
If desired, replace the peak above the visor, and finally always replace both lateral latches (see instructions above).
6.6
Close the visor completely.
WARNING
-
Make sure that the mechanisms are working properly. Open and close the visor making sure that the mechanisms hold it in
the different positions.
-
If necessary, repeat the above-mentioned steps.
-
If the peak is assembled over the visor check the proper functioning as described previously.
-
Do not use the helmet if the visor and the lateral latches have not been assembled properly.
-
Do not remove the side mechanisms from the shell.
-
Should any of the side mechanisms fail or be damaged, please refer to a Nolan authorized dealer.
6
6
Publicidad
