Structure And Functions; Battery Charging - Cleaning Machines KF45E Manual Del Usuario

to the relative sections for a detailed description of
these steps:
Heck the battery charge level and charge, if neces-
sary.
Mount the brushes or scraper disks (with the abra-
sive disks) that are suitable for the surface and
work involved.
Mount the squeegee, check that it is solidly at-
tached and connected to the suction hose and that
the drying blades are not too worn.
Make sure that the recovery tank is empty. If not,
empty it completely.
Check and completely close the detergent solution
release control.
Fill the detergent solution tank with a mix of clean
water and non-foaming detergent in an adequate
concentration through the anterior hole. Leave 2
cm between the mouth of the plug and the level of
the liquid.
☞
( ) To avoid risks, become familiar with the ma-
chine movements, carrying out test runs on a large
surface without obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the following
simple but important operations:
- Identify the work area, moving all possible obsta-
cles out of the way; if the surface is very extensive,
work in contiguous and parallel rectangular areas.
- Choose a straight work trajectory and begin work-
ing from the farthest area to avoid passing over
areas that have already been cleaned.

6.2 STRUCTURE AND FUNCTIONS

PHOTO A KF 45E
1 WATER OUTLET ADJUSTING LEVER
2 SUCTION MOTOR SWITCH
3 BRUSH MOTOR SWITCH
4 GENERAL ON/OFF SWITCH
PHOTO B KF 45E
1 SQUEEGEE LIFT/LOWER LEVER
2 BRUSH PLATE LIFT/LOWER LEVER
3 RECOVERY TANK DRAIN HOSE
4 POWER SUPPLY CABLE
PHOTO C KF 45BBC
1 BATTERY POWER TEST
2 GENERAL ON / OFF KEY SWITCH
3 WATER OUTLET ADJUSTING LEVER
4 SUCTION MOTOR SWITCH
5 BRUSH MOTOR SWITCH
PHOTO D KF 45BBC
1 BATTERY CONNECTOR
2 BRUSH MOTOR THERMAL BREAKER
3 SQUEEGEE LIFT/LOWER LEVER
4 BRUSH PLATE LIFT/LOWER LEVER
5 RECOVERY TANK DRAIN HOSE
6 BATTERY CHARGER POWER SUPPLY
CABLE
7 BUILT-ON BATTERY CHARGER
PHOTO E
1 BATTERY COMPARTMENT OPENING
KNOB
2 SOLUTION TANK FILLING OPENING
PHOTO F
1 BATTERY COMPARTMENT WITH 12V
BATTERIES
2 BATTERY CONNECTION WIRING
3 OPENING CLIP SPRING
PHOTO G
BATTERY CONNECTION DIAGRAM
PHOTO H
1 BATTERY CHARGER COVER
2 RED LED - BATTERY DISCHARGED
3 GREEN LED - FULL BATTERY CHARGE
4 DIP-SWITCHES
5 PLASTIC CAP
6 DIP-SWITCH NR. 1 FOR PB-ACID/GEL
BATTERY SETTING
PHOTO I
1 SQUEEGEE BUMPER WHEEL
2 SQUEEGEE PRESSION ADJUSTING KNOB
3 SUCTION HOSE
4 SQUEEGEE BLADES REPLACEMENT
KNOB
5 SQUEEGEE WHEEL
6 SQUEEGEE FIXING KNOB
7 SQUEEGEE INCLINATION ADJUSTING
KNOB
PHOTO L
1 HOOD OF SUCTION FILTER COMPAR-
TMENT
2 BATTERY COMPARTMENT OPENING
KNOB
3 SOLUTION TANK FILLING OPENING
4 RECOVERY TANK
5 SOLUTION TANK
6 SPLAH GUARD
PHOTO M
1 SUCTION FILTER
2 RECOVERY TANK INSPECTION PLUG

6.3 BATTERY CHARGING

Connect the patch cord to the power cable of the
battery charger ( Photo D - 2 ) and to the mains
power.
30
KF 45BBC
KF 45BBC
KF 45BBC
KF 45BBC
KF 45E - KF 45BBC
KF 45E - KF 45BBC
KF 45E - KF 45BBC