Silver Eagle SE405 Manual De Instrucciones página 2

FAILURE TO OBSERVE THESE WARNINGS COULD RESULT IN INJURY
THIS INSTRUCTION
IMPORTANT SAFETY INFORMATION.
READ THIS INSTRUCTION MANUAL CAREFULLY
AND UNDERSTAND ALL INFORMATION BEFORE
OPERATING THIS TOOL.
• Always operate, inspect and maintain this tool in
accordance
Institute Safety Code of Portable Air Tools (ANSI
B186.1) and any other applicable safety codes
and regulations.
• For safety, top performance and maximum durability
of parts, operate this tool at 90 psig; 6.2 bar max
air pressure with 3/8" diameter air supply hose.
• Always wear
protection
maintenance on this tool.
• High sound levels can cause permanent hearing
loss. Always use hearing protection as recommended by
your employer or OSHA regulation while using this tool.
• Keep the tool in efficient operating condition.
• Operators
physically able to handle the bulk, weight and
power of this tool.
• Air powered tools can vibrate during use. Vibration,
repetitive motions or uncomfortable positions over
extended periods of time may be harmful to your
hands and arms. Discontinue use of tool if discomfort,
tingling feeling or pain occurs. Seek medical advice
before resuming use.
• Compressed air can can cause severe injury. Never
direct air at yourself or others. Always turn off the
air supply, drain hose of air pressure and detach tool
from air
adjusting any accessory on this tool, or before
performing any maintenance on this tool. Failure to
do so could result in injury. Whip hoses can cause
serious injury. Always check for damaged, frayed
or loose hoses and fittings, and replace immediately.
Do not use quick detach couplings at tool. See
instructions for correct set-up.
OPERATION
The air regulator knob can be used as an air throttle and can be used for
setting positive speed control. Lift the air regulator lever up for maximum
speed.
Let the sander do the work. The normal weight of the machine is sufficient
for efficient sanding. Do not put additional pressure on the machine. This will
only slow down the speed of the pad, reduce sanding efficiency and put an
SE405
SE405_manual_062706.indd 2
SE405 6" Dual Action Quiet Sander
MANUAL CONTAINS
with American National Standards
impact-resistant eye and
when operating or performing
and maintenance personnel must
supply before installing, removing
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
• Anticipate and be alert for sudden changes in motion
during use of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Tool shaft may continue to rotate briefly after throttle is
released. Avoid direct contact with accessories during and
after use. Gloves will reduce the risk of cuts or burns
face
• Keep away from rotating end of tool. Do not wear
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
• Never mount a grinding wheel on a sander. A grinding wheel
that bursts can cause very serious injury or death when not
properly guarded. Inspect backing pad before each use. Do
be
not use if cracked of damaged.
• Avoid direct contact with moving sanding pad to prevent
pinching or cutting of hands or other body parts.
• Use accessories recommended by Matco Tools.
• Do not lubricate tools with flammable or volatile liquids
such as kerosene, diesel or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
or
additional burden on the motor. Start the sander off the work, set it down
on the work evenly and move it slowly back and forth in wide, overlapping
areas. When finished sanding, lift it off the work before stopping the motor.
2 06/27/06
7/11/06 10:55:33 AM