Seav BeSAFE RX NEW Manual De Instrucciones página 13

NOTE: The OUT1 Bistable mode is not allowed if the Anti Pass-Back function was previ-
ously activated.
RELAY OUTPUT OPERATION (OUT 2)
With the receiver you can select the OUT2 Timed relay output function (O2-T).
To select the OUT2 Timed function, go to the O2-T storage position and press SEL and
SET: all Digits will start flashing, at the same time use the UP or DOWN button to select a
time between 001 and 999 seconds, press SET to confirm (STOR will show on the display)
and programming will be complete. In this way at each transit you will have activation of
OUT2 relay and subsequent inhibition of further commands until the end of the set time.
NOTE: the Timed operating mode with a pre-set time of 000 seconds is selected in the
default configuration.
SAFETY PASSWORD (PASS)
Once you have finished programming the Receiver, you can store in the PASS (default = OFF)
position a numerical password to disable or enable programming of the receiver, as follows:
use the UP or DOWN button to go to the PASS storage position and press SEL and SET:
all Digits 1,2,3,4 and the KEYBOARD, NFC DEVICE, REMOTE CTR, TAG DEVICE LEDs will
start flashing, at the same time use the UP or DOWN button to select a number between
0001 and 9999 as desired and press SET (STOR will be displayed) and password program-
ming will be complete. From this moment on the settings will be displayed without the
possibility of editing them.
To remove the previously entered Password and edit the receiver settings, use the UP
or DOWN button to go to the PASS storage position and press SEL and SET: all Dig-
its 1,2,3,4 and the KEYBOARD, NFC DEVICE, REMOTE CTR, TAG DEVICE LEDs will start
flashing, at the same time use the UP or DOWN button to select the key number chosen
previously and press SET, the display shows "SURE" (are you sure?) then pressing the
SET button again, the display will show "DELE" or Password removed.
Repeat the above operation to enter a new Safety Password.
NOTE: if you enter a wrong password you have to wait 5 minutes to repeat the operation
and then 1 hour.
RECEIVER SETTINGS DISPLAY
With the receiver you can display in succession all of the previously stored settings, as
follows: use the UP or DOWN button to go to the DISP storage position and press SEL,
the display will show in succession all of the previously stored settings. Instead, by going
on each single setting and pressing SEL, the display will show only the configuration
relative to the specific function.
RESET:
If you need to reset the factory configurations (operation allowed only if Pass = OFF), press
SEL, SET, UP and DOWN simultaneously and continuously for a few seconds, The display
shows "SURE" (are you sure?) Then pressing the SET button you will get off the KEYBOARD
Led NFC DEVICE, REMOTE CTR and TAG DEVICE and the display will show the location "- - - -".
Warning: Resetting will also erases the DATE and TIME.
NOTE: the display turns off after 1 minute of inactivity to save energy.
OUT 1 OUTPUT CONTACT J4 SELECTION JUMPER (NO/NC)
The receiver has a Jumper (J4) for selection of the type OUT1 relay output contact.
J4 pos. 1-2 = OUT1 relay contact, Normally Closed (NC) type.
J4 pos. 2-3 (default) = OUT1 contact, Normally Open (NO) type.
SELECTION (ON/OFF) TERMINATION RESISTANCE
The receiver communicates with the TAG Reader, Keyboard and NFC Reader devices via
standard RS485. Connections can be made with up to 100 m length cables.
If there are communication problems, we recommend moving Jumper J3 to position 1-2
(insertion of termination resistance) on the devices at the ends of the connections:
J3 pos. 1-2 = termination resistance inserted.
J3 pos. 2-3 = termination resistance not inserted (default).
:
attention
- The 3V (CR2032) Lithium battery must be replaced every
two years to ensure maintenance of the Date and Time
settings.
- To replace the discharged battery slide away the plastic lid,
extract the battery in use and insert a new one, respecting the
polarity indicated on the container.
- The used battery must be disposed of in the appropriate
containers.
ADVANCED FUNCTIONS WITH INT 2292 INTERFACE
The receiver can be connected to an INT 2292 interface supplied optional for saving and/
or editing the operation settings on a MicroSD (FAT 32 pre-formatted). The MicroSD can
also be inserted in a PC and consulted via the BeSafe RX New Windows Application.
The data in the receiver can be consulted in two ways: MicroSD card on the INT 2292 and
entered on a PC (not real-time) or MicroSD card inserted on the INT2292 and connected
to the PC via MicroUSB cable (in time real) via the Windows Web App x Seav downloaded
from the site with detailed installation instructions.
13