Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
INSTRuCTIONS MANuAL
Safety precautions
The device may only be connected to supply voltage which is in
compliance with the technical data shown on the serial plate.
Installation, initial start-up and maintenance may only be
performed by trained personnel.
530 MX 01 B
16-05-2012
160
140
Operation is not
120
possible
100
80
60
40
Operating Range
20
0
50
100
150
200
250
300
Cable Length (m)
yellow LED
"Output Relay"
Potentiometer
green LED
"Delay Time"
"Ready"
DIP Switch 2
Potentiometer
"Sensitivity"
"Sensitivity"
DIP Switch 1
"Work/<O-C.
Current"
www.bamo.eu
Amplifier relay ES 2001
+
Electrical connection
Power Supply
L1 N (AC)
+
-
(DC)
12
11
L+ N-
1
14
ON
22
OFF
21
24
E0 E1 E2
Filling pump relay/contactor
is energized when MIN electrode
MAX Electrode
is exposed, ... and dropped out when
MAX electrode is immersed.
MIN Electrode
+
Ref. Electrode
Wiring Diagram 1: Filling the Container
Power Supply
L1 N (AC)
+
-
(DC)
12
11
L+ N-
1
14
ON
22
OFF
21
F
24
E0 E1 E2
Discharge pump relay/contactor
MAX Electrode
+
is energized when MAX electrode
MIN Electrode
is immersed, ... and dropped out when
MIN electrode is exposed.
Ref. Electrode
Wiring Diagram 2: Draining the Container
Power Supply
L1 N (AC)
+
-
(DC)
+
Discharge pump relay dropped out
when the MIN electrode is exposed, or if
interference/power failure/cable rupture
occures at electrode relay
MIN Electrode
Ref. Electrode
Wiring Diagram 2: Empty Alarm
Power Supply
L1 N (AC)
+
-
(DC)
12
L+ N-
11
1
14
ON
22
OFF
21
24
E0 E1 E2
Overflow Alarm (DIP S1= ON):
Alarm signal relay K1dropped out when
MAX electrode is immersed or if
MAX Electrode
interference/power occurs at electrode
Overflow Alarm (DIP S1= OFF):
Ref. Electrode
Alarm signal relay K1 is energized when
MAX electrode is immersed or if
Wiring Diagram 3:
interference/power occurs at electrode
Overflow Alarm
---> Connect relay K1 to terminal 12.
(AC)
Control Voltage
(AC)
+
Filling Pump
K1
Relay / Contactor
(AC)
Control Voltage
(AC)
+
Discharge Pump
K1
Relay / Contactor
(AC)
Control Voltage
(AC)
+
Enable
K1
Discharge
(AC)
(AC)
+
Control Voltage
Alarm Signal
K1
Publicidad
Manuales relacionados para Bamo ES 2001
Resumen de contenidos para Bamo ES 2001
- Página 1 INSTRuCTIONS MANuAL Amplifier relay ES 2001 (AC) Electrical connection Safety precautions The device may only be connected to supply voltage which is in Control Voltage Power Supply compliance with the technical data shown on the serial plate. L1 N (AC)
- Página 2 BEDIENuNGSANLEINTuNG Elektrodensteuerung ES 2001 Elektrischer Anschluss Sicherheitshinweise Montage, Inbetriebnahme und Wartung darf nur durch Fach- personal ausgeführt werden! Gerät nur an die in den technischen Daten und auf dem Typ- schild angegebene Spannung anschließen (bei DL Polarität beachten) ! Technische Daten Versorgungsspannung: 230V AC, ±10%, 50-60Hz,...
- Página 3 (AC) MISE EN SERVICE Relais amplificateur ES 2001 Raccordement électrique Précautions L’alimentation doit être conforme aux valeurs spécifiées sur (AC) la signalétique ainsi que dans les caractéristiques techniques. Tension de commande Alimentation L1 N (AC) L’installation, la mise en service et la maintenance doivent (DC) être effectuées par des personnels qualifiés.
- Página 4 (AC) MANuAL DE INSTRuCCIONES Controlador de nivel ES 2001 Conexión eléctrica Advertencias Conecte el aparato sólo a la tensión de alimentación indicada Tensión de mando en los datos técnicos y la placa de tipo. Alimentación eléctrica L1 N (AC) Del montaje, puesta en servicio y mantenimiento del aparato...