Specific Safety Rules - Matco Tools MUC122SP Instrucciones De Operación

breakage of parts, and any other condition that may affect
the tool's operation . If damaged, have the tool serviced before
using . Many accidents are caused by poorly maintained tools .
RPM RPM RPM
27 . RPM of the accessory must exceed tool RPM.
28 . Never use grinding wheels, wire brushes or cutoff wheels
with this tool .
29 . Use only accessories that are recommended by the
manufacturer for your model . Accessories that may be
suitable for one tool may create a risk of injury when used
on another tool .
30 . This product may contain one or more chemicals known to
the State of California to cause cancer and birth defects or
other reproductive harm . Wash hands thoroughly after
handling.
Service
25 . Do not use (or modify) the tool for any other purpose than
that for which it was designed without consulting the
manufacturer's authorized representative .
26 . Tool service must be performed only by the MATCO
authorized service centers listed . Service or maintenance
performed by unqualified personnel may result in a risk of
injury . Repair by unqualified personnel, use of unauthorized
parts, and failure to follow maintenance instructions may
create a risk of shock or injury .
OPERATING INSTRUCTION
Installing Or Removing Battery Pack
(See Fig.1, Fig.2)
1 . Your new battery pack is not
fully charged . You may need
to charge it before use .
2 . Make sure the switch is in the
"off" position before insertion/
removal of a battery pack .
3 . To remove a battery pack, depress
both tabs on either side of the
battery and pull downward .
4 . To insert a battery pack, align the
battery with the tool housing and
push battery inward until click
indicating battery is fully installed .
Charging The Battery Pack
(See Fig.3)
1 . Battery may not charge when
it is above a certain preset
temperature limit . Allow
temperature of battery to
cool before charging .
2 . The charge process will take less
than one hour .
3 . After charging, unplug the charger
from the power source and stow
away in a safe place .
MUC122SP
MUC122SP 12V Surface Prep Tool
Fig. 1
Fig. 2
Fig. 3
3
SAVE THESE INSTRUCTIONS!

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product replace strict
adherence to cordless product safety rules. If you use this
tool unsafely or incorrectly, you can suffer serious personal
injury .
1 . Hold tool by insulated gripping surfaces when performing an
operation where the tool or accessory may contact hidden
wiring . Contact with a "live" wire will also make exposed
metal parts of the tool "live" and shock the operator .
2 . Be aware that this tool is always in operating condition,
because it does not have to be plugged into an electrical
outlet .
3 . Always be sure you have firm footing .
4 . Be sure no one is below when using the tool in high locations .
5 . Hold the tool firmly and use both hands .
6 . Keep hands and hair away from rotating parts .
7 . Do not leave the tool running . Do not force tool to stay in
the "on" position . Operate the tool only when hand-held .
8 . Do not touch the tool, accessory or the workpiece
immediately after operation; they may be extremely hot
and could burn your skin .
9 . Some material contains chemicals which may be toxic .
Take caution to prevent working dust inhalation and skin
contact . Follow material supplier safety data .
WARNING:
MISUSE or failure to follow the safety rules stated in this
instruction manual may cause serious personal injury.
Tool Operation
1 . Tighten backing pad in a clockwise direction using the
included spanner wrench .
2 . Attach polishing pad to the backing pad . Center properly .
3 . Press trigger to activate .
4 . For removal of velcro pad attachment use wrench key to fix
the shaft and turn the velcro pad attachment in counter
clockwise direction .
NOTE: During operation, safety goggles should always be worn to
guard against flying rust & chips (users & bystanders) .
WARNING:
After mounting sandpaper, start this tool under a bench in order
to make sure sandpaper is firmly attached.
07/14/15