Matco Tools MT2868 Instrucciones De Operación

Matco Tools MT2868 Instrucciones De Operación

Publicidad

Idiomas disponibles

Idiomas disponibles

DUAL PISTON STRAIGHT
LINE SANDER
WARNING
RATED RPM OF THE ACCESSORY USED
MUST EXCEED THE MAXIMUM TOOL
RPM SHOWN
ALWAYS READ
INSTRUCTIONS BEFORE
USING POWER TOOLS
ALWAYS WEAR
SAFETY GOGGLES
WEAR DUST MASK
WEAR HEARING
PROTECTION
AVOID PROLONGED
EXPOSURE TO
VIBRATION
Pad Size ....................................................16" x 2-1/2"
Stroke Length ....................................................... 5/8"
Stroke Per Min ....................................................1800
Recommended Air Pressure: ......................... 90 PSI
Average Air Consumption: ........................... 2.3 cfm
Recommended Hose Size: ................................. 3/8"
Sound Level: ..................................................87 dBA
Height: ............................................................ 6-3/16"
Overall Length: ..................................................... 16"
Weight: ............................................................6.8 lbs.
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
S P E C I F I C A T I O N S
WARNING
Copyright © Professional Tool Products, 2013
MT2868
• Operating Instructions
• Warning Information
• Parts Breakdown
MT2868
All rights reserved

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Matco Tools MT2868

  • Página 1 MT2868 • Operating Instructions • Warning Information • Parts Breakdown DUAL PISTON STRAIGHT LINE SANDER S P E C I F I C A T I O N S MT2868 Pad Size ............16" x 2-1/2" Stroke Length ............5/8" Stroke Per Min ............1800 Recommended Air Pressure: ......
  • Página 2 MT2868 DUAL PISTON STRAIGHT LINE SANDER WARNING faIlure TO OBserVe These WarnIngs cOuld resulT In InJury • Keep body working stance balanced and firm. Do ThIs InsTrucTIOn Manual cOnTaIns not overreach when operating the tool. IMPOrTanT safeTy InfOrMaTIOn. • Anticipate and be alert for sudden changes in motion read ThIs InsTrucTIOn Manual carefully during start up and operation of any power tool.
  • Página 3: Air Supply

    MT2868 DUAL PISTON STRAIGHT LINE SANDER feaTures • Dual piston for fast material removal • Sanding pad has positive locking clamps and can also use PSA paper. aIr suPPly TrOuBleshOOTIng Tools of this class operate on a wide range of air pressures. It is Other factors outside the tool may cause loss of power or erratic recommended that air pressure of these tools measures 90 PSI action. Reduced compressor output, excessive drain on the air line, at the tool while running free. Higher pressure and unclean air moisture or restrictions in air pipes or the use of hose connections will shorten tool life because of faster wear and may create a of improper size or poor conditions may reduce air supply. If...
  • Página 4 MT2868 DUAL PISTON STRAIGHT LINE SANDER ITEM PARTS NO PARTS NAME ITEM PARTS NO PARTS NAME RS288B01 Screw RS288B22 Screw RS286802 Front Cap RS288B23 Trigger RS288B03 Piston RS288B24 Pin RS288B04 Plug RS288B25 Screw RS288B05 Piston Ring RS288B26 Hex. Nut RS288B06 Front Gasket RS288B27 Washer...
  • Página 5: Lijadora En Línea Recta Con Pistón Doble

    MT2868 • Instrucciones de Operación • Inforación de advertencia • revisión de refacciones LIJADORA EN LÍNEA RECTA CON PISTÓN DOBLE E S P E C I F I C A C I O N E S MT2868 Tamaño de la almohadilla ........... 16" x 2-1/2"...
  • Página 6: Operación

    MT2868 LIJADORA EN LÍNEA RECTA CON PISTÓN DOBLE ADVERTENCIA EL INCUMPLIMIENTO DE OBSERVAR ESTAS ADVERTENCIAS PUEDEN RESULTAR EN ALGUNA LESIÓN separación. Vea las instrucciones por la instalación esTe Manual InsTruccIOnes correcta. cOnTIene InfOrMacIÓn IMPOrTanTe de segurIdad. lea cuIdadOsaMenTe esTe • Resbalarse, t ropezarse y /o c aerse d urante l a o peración d e Manual InsTrucTIVO y cOMPrenda TOda herramientas neumáticas puede ser una causa mayor de...
  • Página 7: Características

    MT2868 MT2868 LIJADORA EN LÍNEA RECTA CON PISTÓN DOBLE CARACTERÍSTICAS • Su pistón doble permite la rápida remoción del material • La almohadilla para lijado tiene abrazaderas de cierre seguro y también puede utilizar papel PSA. alIMenTacIÓn de aIre dIagnÓsTIcO de aVerÍas Las herramientas de esta categoría operan dentro de un rango Otros factores independientes de la herramienta pueden amplio de presión de aire. Al trabajar libremente, se recomienda ocasionar la pérdida de potencia o alguna acción errática. Las que la presión de aire de estas herramientas mida a un 90 PSI en...

Tabla de contenido