OWNER'S MANUAL
SETUP
PLEASE REFER TO THE EXPLODED VIEW DRAWING IN THIS MANUAL IN ORDER TO IDENTIFY PARTS.
1.
Place the hydraulic power unit in an upright position. Secure the legs (index #2-5) to the cylinder (index #1-1) with the bolts
(index #2-3) and washers (index #2-4). Do not tighten.
2.
Secure swivel casters (index #2-1 and #2-2) to leg caster brackets as shown in the exploded view drawing on page 5.
3.
Tighten the hardware that secures the legs (index #2-5) to the cylinder (index #1-1).
4.
Place the saddle assembly (index #3-31) on the stud protruding from the top of the hydraulic unit assembly. Align the hole in the
saddle with the hole in the stud, and secure with the bolt (index #3-26) and nut (#3-27).
5. The hydraulic power unit is equipped with two reservoir fill screws (index # 1-37 and 1-38). The closed filler screw is installed in
the reservoir at the factory so the jack will not leak during shipment.
IMPORTANT: REPLACE THE RESERVOIR FILLER SCREW WITH THE VENTED RESERVOIR SCREW BEFORE USING THE JACK.
6.
Sometimes air gets trapped in the hydraulic system during shipping and/or handling. Evidence of an air bound system is when
pumping the foot pedal feels spongy and/or the jack will not pump full incremental strokes.
PURGING AIR FROM THE HYDRAULIC SYSTEM:
a.
Depress the release foot pedal while simultaneously
pumping the jack about 15 incremental pump strokes.
b. Remove your foot from the release pedal and pump the
jack to maximum extension.
c.
If the secondary ram seems to be spongy or does not
pump up normally, insert an Allen wrench in the small
Allen socket set screw in the side of the secondary
cylinder nut. (See Figure 1) Slightly turn the set screw in
a counterclockwise direction while lightly depressing
the pump pedal. This procedure is similar to bleeding
air out of an automotive brake line. Repeat the
procedure until there are no bubbles in the oil that
escapes from behind the Allen socket set screw.
d. Close the Allen socket set screw by turning it in a
clockwise direction until tight. Repeat steps "a" and
"b".
e.
If the condition seems better, repeat steps "a"
through "d" until air is purged from the system.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1.
Lift the vehicle to the desired work height and support the vehicle in accordance with the lift manufacturer's recommended
support procedure and all the instructions and warnings in this manual.
2.
Use an under hoist stand rated greater than the weight of the engine to support the engine before unbolting the transmission
from the engine or bolting the transmission to the engine.
3.
Position the transmission jack directly under the transmission. Depress the large foot pedal up and down in order to raise the
saddle to a height very close to the center of balance point of the transmission oil pan but do not touch the transmission.
4.
Adjust the ratchet arms on the saddle so that the bent up section of the arms will fit in the mounting flange around the
perimeter of the transmission oil pan. Slowly and gently pump the jack so the connection is made and then secure the
transmission to the jack's saddle with the tie down strap provided. Sometimes it is necessary to turn the fore and aft and side to
side tilt knobs so the saddle is in the proper alignment with the transmission pan before securing the load to the saddle.
5.
Make sure the tie down strap is very tight when securing the transmission to the saddle and before raising or lowering the
transmission.
6.
Remove the transmission from the engine according to instructions in the vehicle service manual.
7.
Once the transmission has been disconnected from the engine, very slowly depress the release pedal to make sure the jack's
saddle and transmission do not hang up on any undercar components, wiring, fuel lines, etc. Continue to lower the jack all
the way down.
8. When installing a transmission, follow the above instructions but in the applicable order and according to the vehicle
manufacturer's installation procedure.
7795
TRANSMISSION JACK
Figure 1
3
MODEL 7795
CAPACITY: 1/2 TON
TELESCOPIC
Location of
Allen socket set
screw in secondary
cylinder nut
rev. 05/05/11