Kova K265113-P00070-BN Manual De Instrucciones

INSTALL INSTRUCTIONS
Product
12-in Round Flush Mount Ceiling Light
KPN Model Number
K265113-P00070-BN
Brushed Nickel
kovaproducts.com Rev 1.0 | 03/2020
Safety Information
WARNING: To prevent electrical shock, turn power off at the fuse box before
installation.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of
sheet metal or other sharp objects.
WARNING: Risk of fire or electric shock. Installation of this surface mount assembly
requires a person familiar with the construction and operation of the
luminaire's electrical system and the hazard involved. If not qualified, do
not attempt installation. Contact a qualified electrician.
WARNING: Risk of fire or electric shock. Do not alter, relocate, or remove wiring,
lampholders, power supply, or any other electrical component.
WARNING: Risk of shock. Do not use where directly exposed to water.
WARNING: Not for emergency lighting.
WARNING: This product must be installed in full accordance with applicable
electrical and building codes by a person familiar with the construction
and operation of this fixture and all involved hazards. Installation should
be performed by a qualified electrician in accordance with the National
Electrical code and relevant local codes.
WARNING: All wiring connections should be capped with UL-approved wire
connectors. Connect fixture to supply wires rated for a minimum of 194 °F
(90 °C). Do not exceed maximum wattage marked on luminaire label. The
fixture is intended to be connected to a properly installed and grounded
UL-listed junction box.
CAUTION: Follow all lamp manufacturer's warnings, recommendations and
restrictions for: driver type, burning position, mounting locations/methods,
replacement, and recycling.
CAUTION: Wear gloves and safety glasses at all times when removing fixture from
carton, installing, servicing, or performing maintenance.
CAUTION: Avoid direct eye exposure to the light source while it is on.
CAUTION: Account for small parts and destroy packing material, as these may be
hazardous to children.
• For indoor use only.
• Suitable for damp locations.
• Suitable for operation in ambient temperatures not exceeding 104 °F (40 °C).
• This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation. Any changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate the
equipment.
Dimming
This product is compatible with most common residential type dimmers. Dimming
performance depends on the dimmer.
Pre-Installation
Recommended Tools (not included)
Gloves Safety goggles Screwdriver Electrical tape
Product Description
C
A
B
D
E
F
Part Description Qty. Part Description
A Screws 1 D Fixture Lens
B Fixture Pan 1 E Fixture Ring
C Wire Nuts 3 F Cap Nuts
Before You Begin
WARNING: Ensure power is turned off at the circuit breaker.
1 Prepare the Outlet Box
1
A
Black
Green
(Ground Wire)
White
1. Thread the screws (A) into the appropriate holes on the outlet box.
2. Pull the black supply wire, the white supply wire, and the house ground wire out
of the outlet box (1).
2 Connect the Electrical Wires
Black
Green (Ground Wires)
White
C
IMPORTANT: Do not allow the fixture to hang from the wires.
1. Hold the fixture firmly.
2. Connect the black fixture wire to the black supply wire using a wire nut (C).
3. Connect the white fixture wire to the white supply wire using a wire nut (C).
4. Connect the fixture ground wire to the supply ground wire using a wire nut (C).
5. Wrap all wire connections with electrical tape to ensure a secure connection.
6. Tuck all wires back into the outlet box.
CAUTION: If house wiring does not include a ground wire, consult your local electrical
Qty.
code for approved grounding methods.
1
1
3 Install the Light Fixture
3
C
F
1. Align the keyhole slots on the fixture pan (B) with the screws (A) in the outlet box
(1).
2. Rotate the fixture pan (B) clockwise to slide the screws (A) into the narrow ends of
the keyhole slots. Tighten the screws (A) firmly.
3. Slide the fixture lens (D) and fixture ring (E) onto the fixture pan (B) and secure
with three cap nuts (F).
Care and Maintenance
Wipe the surface of the fixture with a with a clean, dry cloth.
Product and Warranty Information
For product and warranty information, please visit kovaproducts.com.
1
A
B
D
E