Technical Data; Noise/Vibration Information - BOS PTK 14 EDT Manual Original

OBJ_BUCH-1439-003.book Page 11 Thursday, November 19, 2015 10:48 AM
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Tacker head
2 Selector switch for DuoTac-Automatic
3 Handle
4 Trigger
5 Thumbwheel for hammer-force preselection
6 Magazine release button
7 Refill indicator
8 Staple strip*
9 Magazine
10 Nail strip*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Tacker
Article number
Impact rate
Intermittent operation (S2)
Fastener
– Staple strip
– Width
– Length
Fastener
– Nail strip
– Length
Magazine capacity, max.
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-16.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a and uncertainty K determined ac-
h
cording to EN 60745:
2 2
a =7,5 m/s , K=1,5 m/s .
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
Bosch Power Tools
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745+1, EN 60745+2+16,
EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
PTK 14 EDT
Henk Becker
0 603 265 5..
Executive Vice President
-1
min 30
Engineering
min 10
Type 53
mm 11,4
Robert Bosch Power Tools GmbH
mm 6 –14
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
mm Type 48
Assembly
mm 14
100
Loading the Magazine (see figures A1
 Before any work on the machine itself, pull the mains
kg 1,1
/II
 Use only original Bosch accessories. The precision parts
– Turn the power tool around.
– Press release buttons 6 and pull out the magazine 9 toward
– Insert the staple strip 8 or the nail strip 10. Hold the tacker
– Insert the magazine 9 again until it engages.
 Do not exert any force when opening, loading and in-
Operation
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
plug.
of the power tool, such as the magazine, the striker and the
shot duct, are matched to Bosch staples and nails. Other
manufacturers use other steel qualities and sizes.
the rear.
at a slight angle when inserting the nail strip 10, so that the
nails face against the sidewall.
serting the magazine.
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
English | 11
A2)
–
1 609 92A 1XJ | (19.11.15)