Joovy Tricycoo 0017X Manual Del Usuario página 3

Adult assembly required. Tools required (not included): Phillips Screwdriver. Choking Hazard to children under the
age of 3 years – contains small parts prior to assembly. Some screws may have sharp edges and sharp points.
2 Installing the Rear Wheels
• Keep children away while assembling.
• Insert an Inner Rear Wheel Hub into either end of the rear axle cylinder on the rear of the tricycle frame. See Figure 2.
• Insert the axle into one of the rear wheels (ensuring that the side with the 8 holes faces out). Slide the axle (with the Rear Wheel)
thru the Inner Rear Wheel Hub and the rear axle cylinder. See Figure 3.
• Insert the other Inner Rear Wheel Hub into the opposite end of the rear axle cylinder.
• Slide the other Rear Wheel over the axle (ensuring that the side with the 8 holes is facing out). Slide the large washer over the axle.
• Insert the snap pin straight leg into the small hole in the axle. Push it firmly into this hole until the round portion of the other leg snaps
completely around the outside of the axle. See Figure 4.
NOTE: The snap pin is curved (concave) to make insertion easier.
• Install a hubcap onto each wheel by aligning the 4 tabs with the 4 slots in the wheel. Ensure that ALL 4 tabs have engaged securely
and the hubcaps cannot be pulled off. See Figure 5.
3 Front Wheel Assembly
• Place the fender onto the front wheel tube making sure you push the fender all the way down. See Figure 6.
• With the long part of the fender facing forward insert the front wheel tube into the front steering hub of the tricycle frame. See Figure 6.
• Identify the 2 piece spacer (assemble if necessary) and slide it over the top of the front wheel set. Make sure to push the spacer all the
way down. See Figure 7.
If you intend to use the optional baby surround system, slide the baby surround connector onto the tricycle frame.
See Figure 8. If not using the baby surround system then disregard this NOTE.
4 Handlebar Assembly
NOTE: If not using the baby surround system, make sure that the baby surround connector is NOT attached to the tricycle frame.
• Insert the handlebar onto the front wheel tube. See Figure 9.
NOTE: The handlebars should be mounted with the bars leaning forward.
• From the front of the product, insert the philips head bolt into the middle hole of the handlebar column and push it all the way through.
Attach the Nylock nut to the bolt and tighten using the tool provided. See Figure 10.
• Fit the front half of the handlebar cap thru the bottom hole on the front of the handlebar.
• Snap the back half of the handlebar cap to the front. Secure the handlebar caps with the pointed philips head screw. See Figure 11.
NOTE: Pull on the handlebar and the handlebar caps to make sure they are secure.
5 Seat Assembly
• Place the seat onto the frame facing forward and line up the hole in the tricycle frame. See Figure 12.
• Secure the seat with the 2 small washers and the seat screw. Tighten the screw securely. See Figure 13.
• Pull on the seat to ensure that it is secure.
6 Push Handle Assembly
• Place the basket onto the rear of the tricycle frame with the opening over the rear steering tube. See Figure 14.
• Next place the cover cap onto the rear steering tube. See Figure 15.
• Insert the upper half of the push handle into the end of the lower handle tube that has the plastic knob on it. Insert it so that the pin
on the upper handle is aligned with the holes in the lower tube and push down until a click is heard and the pin can be seen protruding
from one of the holes. Pull on the upper half to be sure it is secure. See Figure 16. For push handle adjustment, see "Steering with the
Push Handle" section on page 7.
• Insert the push bar into the rear steering tube in the back of the tricycle frame. Make sure to line up the hole in the push bar with the
hole in the tube.
• Insert the knob screw through the hole and secure with a knob nut. Tighten the nut securely. See Figure 17.
The baby surround system should be used for children who are not yet capable of sitting in the seat
without support or who are not capable of pedaling the product by themselves.
7 Attaching/Detaching the Baby Surround (OPTIONAL)
NOTE: If you are not using and have not attached the baby surround connector then skip these steps in this section.
• Insert one of the baby surround arms into one of the sides of the baby surround base.
• Fasten securely in place with a washer head screw. See Figure 18.
• Repeat these steps for the other surround arm.
• Place the baby surround base on the top of the seat back and push down until a click is heard. See Figure 19.
WARNING
!
Keep all small parts out of reach of children at all times.
IMPORTANT NOTE:
WARNING
!
EN FR ES