Assembly; Selecting A Shaping Disk; Initial Use - Silvercrest 313492 Instrucciones De Utilización Y De Seguridad

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Pull the auger
out of the pressing tube
7
Pull the mixing chamber
ing paddle
forward to remove from the
5
housing
. The mixing paddle
2
automatically from the socket.
Remove the drawer
10
for cleaning.

Assembly

Make sure that the device is switched off and
unplug the mains plug from the socket before
assembling.
If you had previously removed the drawer
re-insert this into the housing
used shaping disks
.
16
Push the mixing chamber
housing
(see fig. A). The two guide pins at
2
the upper outer edge of the mixing chamber
should not yet lock into the corresponding
1
sockets on the housing
Insert the mixing paddle
chamber
from above until it locks into place
1
in the relevant socket.
Push the mixing paddle
in the back wall of the housing
Now push the mixing chamber
housing
as far as it will go, so that both
2
guide pins lock into the corresponding sockets
at the upper edge of the mixing chamber
From the front, insert the pressing tube
the opening with the help of the corresponding
socket (see fig. D). In doing so, make sure that
the auger
locks into place in the slots.
7
Insert the auger
into the pressing tube
7
(see fig. E) until it completely disappears.
Fit the front panel
onto the housing
6
lock it in place by turning the fixing screws
clockwise (see fig. F).
Select the desired shaping disk
to the pressing out tube (if necessary hold fast
with one hand). The small nib on the back of
the shaping disk
must lock into place in the
16
silver opening at the end of the pressure roller.
Screw the shaping disk holder
clockwise direction (see fig. F).
.
8
including the mix-
1
releases
5
from the housing
2
,
10
with the un-
2
loosely into the
1
.
2
into the mixing
5
tightly into the socket
5
(see figs. B + C).
2
into the
1
.
1
into
8
8
and
2
15
and fix this
16
tight in a
9
Note: Do not screw the shaping disk
tight. If you do, it will be very difficult to unscrew
after you have finished making pasta (due to
contact pressure).
Attach the lid
by inserting the two teeth into
4
the sockets on the housing
down until you hear it click. Assembly is now
complete (see fig. G).

Selecting a shaping disk

The following 8 shaping disks
the delivery contents (see fig. H):
-
thin spaghetti
16a
-
macaroni - made up of 2 parts
16b
-
triangular
16c
-
thick spaghetti
16d
-
lasagne / ravioli - made up of 2 parts
16e
-
linguine
16f
-
fettuccine
16g
-
pappardelle
16h
Make sure that the shaping disk holder
well fastened so that it doesn't have a negative
effect on your pasta production.
When using the shapes „lasagne / ravioli" and
„macaroni", make sure that you have inserted
the shaping disks
16
first holding the shaping disk
insert with one hand and screwing tight the
shaping disk holder
The length of time it takes to press out pasta
depends on the shaping disk
the small opening, it can take up to 3 minutes
for thin pastas, e.g. thin spaghetti, to be pressed
out.
ATTENTION: During operation, the shaping disk
can only be changed after the pasta machine
16
has been switched off.

Initial use

Connect the mains cable
the back of the device.
too
16
. Press the lid
2
are included in
16
is
9
correctly. We recommend
and the relevant
16
with the other.
9
used. Due to
16
with the socket on
3
GB/MT
4
39

Hide quick links:

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido