Device Features - Comelit Bridge Serie Manual Tecnico

Warning
• Install the equipment by carefully following the instructions given by the manufacturer and in compliance with the standards in force.
• All the equipment must only be used for the purpose it was designed for. Comelit Group S.p.A. declines any responsibility for improper use of the apparatus, for any
alterations made by others for any reason or for the use of non-original accessories or materials.
• All the products comply with the requirements of the 2014/30/UE, 2014/35/UE directives, as certified by the CE mark they carry.
• Do not route the riser wires in proximity to power supply cables (230/400V).
• Do not insert objects or pour liquids into the device.
• Installation, mounting and assistance procedures for electrical devices must only be performed by specialised electricians.
• Cut off the power supply before carrying out any maintenance work.
Serial Bridge Art. 20003101
ON
1 2 3 4 5 6
11 10 9
LED 1
Set dip switches 4, 5 and 6 according to the type of system, as
illustrated in the wiring diagrams.
Always remember to insert (by means of dip switch 4) an end-of-line
resistor between A and B of the 485 connection to the two ends of
the main BUS line.
Introduction
The Serial Bridge module makes it possible to communicate with the SimpleHome home automation BUS and with S-Series and VEDO anti-intrusion
systems. It can be used as follows:
• Weekly schedule programming: sends commands to outputs, zones, scenarios and thermostats within the system.
• WEB Server for system management via any browser (PC, smartphone, tablet).
• Rule management: programs rules with up to 3 elements with AND/OR functions between inputs, outputs or security/home automation timer in order
to generate an event for transmission over the home automation BUS or to the security system.
• Scenario management: programs scenarios which include procedures to be sent to the SimpleHome automation system and/or the S-Series or VEDO
security system.
User setup and management must take place via the WEB interface.

Device features

The Serial Bridge is a Web Server device which, by means of a PC browser, tablet, smartphone, etc. is able to do the following without the
installation of any additional programs:
• Display/control areas of a compatible VEDO or S-Series alarm control unit.
• Display the status of the first 80 wired inputs and the first 48 radio inputs of a compatible S-Series control panel.
• Display the status of all zones (wired and radio) of a compatible VEDO control panel.
• Display/control 400 elements (lights, sockets, timed outputs, analogue inputs, thermostats, scenarios...) with a maximum of 50 rooms, 50
RGB lights and 40 thermostats.
From the Serial Bridge it is possible to configure:
• Up to 32 timers.
• Up to 50 rules with 3 elements each.
• Up to 32 scenario commands with 20 elements each.
The programming manual and the user manual are stored on the SD card for Art. 20003101 and are available to download
from the website www.comelitgroup.com
1
2
3
4
5
6
8 7
LED 2
Description of the Serial Bridge:
1. Connection terminals:
| 2 | TX RS232 S series alarm control unit.
| 3 | RX RS232 S series alarm control unit.
| 5 | GND RS232 S series alarm control unit.
2. Connection terminals:
| D | SimpleHome BUS data terminal.
| + | - | 12/24 Vdc power supply from home automation BUS or
alarm control unit.
3. LED indicating data transmission over home automation BUS:
YELLOW data transmission over BUS.
RED error on BUS.
4. Slot for SD card.
5. USB input (underneath front cover) for PC connection and
SimpleHome system programming.
6. LED indicating operation:
Slow flashing: normal operation.
Quick flashing: no SD card.
7. Ethernet port:
LED 1 lit: connection active.
LED 2 flashing: data transfer in progress.
8. LED indicating data transmission to alarm control units.
9. Reset button.
10. Dip switches:
1-2-3 For future uses.
4 485 terminator.
5 Earth union (default = ON).
6 For power supply to safe part with SimpleHome input.
11. Anti-intrusion BUS connection terminal:
| V+ | 485/232 power supply positive.
| V- | 485/232 power supply negative.
| A | Anti-intrusion data BUS signal A.
| B | Anti-intrusion data BUS signal B.
3