Fault Symptoms - Neumann MINIMISSION Manual Del Usuario

Fault symptoms

®
If your Minimission does not work correctly, follow the trouble shooting guide below
Refer to the Owner's Manual for Minimission
Symptom
Minimission
®
Minimission turns on,
(except that you press the HOME button to
but the Blade Disc does
make it go to the charging base, or the "Enable
not move.
boundary cut" function is operating).
Blades may be damaged. Check condition of the
®
Minimission vibrates.
Blade Disc.
Minimission
day.
Mowing area is too big.
Blades are dull.
Grass is being cut
The cutting height is set too low for the length of
unevenly.
the grass.
Grass or other object has wrapped around the
blade disc.
There is a build-up of grass in the Blade Disc or
Motor Frame Box.
The LED light on the
Charging base does not There is no power.
turn on.
Green light flashing on
The Boundary Wire isn't connected.
charging base.
®
Your Minimission is
inside its territory but
the display says "outside The boundary wire ends are clamped incorrectly.
working area" and the
LED is green.
Poor connection caused by debris on the Charging
Strip.
The charging time is far
more than 2h.
The charging protection program has activated
due to high temperature.
There is no power.
The mower does not
charge.
Does not operate correctly while manually
charging.
Something is clogged in the Blade Disc.
®
Minimission is starting
to have shorter run-
Minimission
times between charges.
The battery may be exhausted or old.
®
The clock is not set to the correct time.
Minimission is not
operating at the correct
Programmed cutting times for Minimission
time.
not correct.
Environmental influences.
®
Minimission can not
correctly dock with the
Poor connection caused by debris on the Charging
Charging Base.
Strip.
The Green light on the
Charging Base turns The charging base is overheating, the LCD will
ON before charging is display "Over temperature".
complete.
®
component information.
Cause
®
is searching for the Charging Base
®
does not work enough hours per
®
is shaking heavily.
. If the fault persists, contact your dealer.
This is normal, Minimission
the Blade Disc does not rotate while it is
searching for the Charging Base automatically.
Check the Blades, and replace them if damaged .
Remove debris and foreign objects from the
blades and blade disc.
Add more hours to the mowing time.
Try decreasing the size of the mowing area or
adding more hours to the mowing time.
Change all the Blades and screws in order to
balance the Blade Disc.
Raise the cutting height and then gradually lower.
Check the Blade Disc and remove the grass or
other object.
Make sure the Blade Disc rotates easily. If
needed, you may take off the Blade Disc and
then remove the debris. See How to Clean.
Check the power cord is connected properly to
the charger and the charger is connected to a
suitable power supply.
Check the boundary wire has been connected
correctly to the charging base. Check there are
no breaks in the boundary wire.
Reverse the boundary wire ends.
Clean the Contact Pins located on the Charging
Base and the Charging Strip on Minimission
using a cloth.
Place the charging base in a shady area or wait
until the temperature has cooled down.
Check the power cord is connected properly to
the charger and the charger is connected to a
suitable power supply.
Refer to manual charging in Owner's manual.
Take off the Blade Disc and clean it.
The grass is too high and too thick.
Check the blade disc and blades, remove debris
and foreign objects from the blades and blade
disc.
Replace battery.
Set the clock to the correct time.
®
are Change the time settings for the mower to start
and stop.
Restart Minimission
Clean the Contact Pins located on the Charging
Base and the Charging Strip on Minimission
using a cloth
Place the charging base in a shady area or wait
until the temperature has cooled down.
Action
®
needs to recharge,
®
®
.
®
7
EN