Setting The Timer; Using The Timer - Denon DRA-F101 Instrucciones De Operación

9

USING THE TIMER

(1) Setting the Current Time (12-hour display)
Example: Setting the current time to 9:30 p.m.
2 3,5,7 4,6
VOLUME
TUNING
MEMORY SOURCE
FUNCTION
TONE TIMER DISPLAY / SET DOWN UP BAND DIRECT
SYSTEM
ON / STANDBY
PHONES
AM-FM STEREO RECEIVER DRA-F101
1
SYSTEM
ON / STANDBY
1
Turn on the power.
TIMER
Press the TIMER button for at least
3 seconds.
• "TIME" flashes on the display.
If the time is already set,
2
"EVERYDAY" is displayed.
Press one of the TUNING buttons
to display "TIME", then perform
step 3.
MEMORY
/ SET
Press the MEMORY/SET button.
• The hours position flashes.
3
(2) Before Setting the Timer
Be sure to set the current time. If the current time is not set, the timer standby indicator ("
2
timer will not function.
2 Be sure to preset the station before setting the timer. (Refer to "Presetting AM and FM stations" on page 14.)
The DRA-F101 is equipped with two types of timers: the everyday time which turns the power on and off at the
2
same times every day, and the once timer that turns the power on and off only once.
Do not change the timer standby mode after the timer is activated (after the timer on time is reached). The timer may
2
not operate properly.
2 It is not possible to set the timer start and end times to the same time.
If the display or operation is not normal, unplug the power cord, then plug it back in while pressing the memory/set
2
button (MEMORY/SET). This restores the tuner to the initial default values. After doing this, reset the presettings,
current time and timer settings.
When setting the timer to operate the CD player do so with a disc loaded and the disc holder closed. The timer will
2
not operate properly if no disc is loaded or if the disc holder is open.
TUNING
Use the TUNING buttons
DOWN UP
to input the hours (PM 9).
• "9" flashes in the hours
position.
4
Press the MEMORY/SET button. MEMORY
/ SET
• "9" stops flashing, remaining lit,
and the minutes position starts
flashing.
5
TUNING
Use the TUNING buttons to
DOWN UP
input the minutes (30).
• "30" flashes in the
minutes position.
6
Press the MEMORY/SET button
at the sound of the chime of a
MEMORY
time service, etc. / SET
• "30" stops flashing, remaining
lit, and the current time is
7
displayed.
The number changes continuously when one of the
tuning buttons (TUNING UP or DOWN) is pressed.
If the time is already set when step 2, 3 is performed,
both the hours and minutes positions flash.
") will not light and the

(3) Setting the Timer

The timer function lets you switch the power between
2
the on and standby modes automatically at the desired
times.
When connected in a system with the DCD-F101, the
2
timer can be used to play a CD.
Example: Using the everyday timer to listen to the
station stored at preset number 3 (FM 98.00 MHz)
from 2:35 p.m. to 2:56 p.m.
2 3, 5, 7, 9,11,13,15,17
VOLUME
MEMORY TUNING
SOURCE
FUNCTION TONE TIMER DISPLAY DOWN UP BAND DIRECT
/ SET
SYSTEM
ON / STANDBY
PHONES
AM-FM STEREO RECEIVER DRA-F101
1,18 4, 6, 8,10,12,14,16
SYSTEM
ON / STANDBY
1
Turn on the power.
TIMER
Press the TIMER button for at least
3 seconds.
• "EVERYDAY" is displayed.
2
If the time is not set, "TIME" is displayed.
Perform steps 3 to 7 on page 15, then start
the timer setting over.
TUNING
Press one of the TUNING DOWN UP
3
buttons to display
"EVERYDAY" or "ONCE".
MEMORY
Press the MEMORY/SET button.
/ SET
• This sets the unit to the timer
setting mode's function
setting mode.
4
Example: When the everyday timer is
selected
ENGLISH
TUNING
Use the TUNING buttons DOWN UP
to switch the function to
"TUNER".
5
The function switches as follows each time
the button is pressed:
: When the TUNING UP button is pressed.
: When the TUNING DOWN button is
pressed.
MEMORY
Press the MEMORY/SET button. / SET
6
• "TUNER" is stored in the
memory as the timer function.
TUNING
DOWN UP
Use the TUNING buttons
to set preset number 3.
7
Press the MEMORY/SET
MEMORY
/ SET
button.
• The preset station is stored in
the memory and the timer on
time setting mode is set.
"E" and "oN" appear
8
alternately in the display in the
steps 8 to 11.
<Setting the timer on
TUNING
time> DOWN UP
Use the tuning buttons to set
the hours position to "PM
2".
9
15