Westinghouse W-630 Manual Del Usuario

Owner's Manual
Indoor Lighting Fixture
Installation Instructions
Fixture Warranty
This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a period
of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration
of components, nor does it cover damages caused through abuse, improver installation, surges in
electric current, or acts of third parties.
This warranty does not cover the costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, please contact us at www.westinghouse-
lighting.com/contact-us.
ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselighting.
com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any
packing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is
essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not
damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components
are damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are
provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before
1985 have supply wires rated 60° C. Consult a qualified electrician before installing.
FIGURE 1.
*GROUND
DRYWALL WIRE
ANCHORS (E)
SIDE HOLE (I)
OUTER HOLES (O)
*OUTLET BOX SCREWS (P)
SCREW (K)
BUTTERFLY NUT (Q)
FACE PLATE (A)
CANOPY (S)
CAP NUTS (B)
STEMS (F)
FIXTURE
BODY (T)
Line art shown may not exactly match the
fixture enclosed. However, the installation
instructions do apply to this fixture.
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
W-630
meet all UL specifications.
032819
1. Turn off power at circuit box to avoid possible electric shock.
3. Position flat side of mounting plate (C) against ceiling at mounting location and mark outer holes
(O) with a pencil.
4. Drill a 1/4 inch hole at each pencil mark then insert drywall anchors (E) by gently tapping with a
hammer.
5. Thread outlet box wires through center opening in mounting plate (C).
6. Position mounting plate (C) with outer holes (O) over drywall anchors (E) and secure with screws
(K), then secure mounting plate (C) to outlet box (J) with outlet box screws (P).
7. Select number of stems (F) to install based on desired fixture length then connect connector (V) to
stems (F) and to each other if applicable. Repeat this step for the second set of stems.
8. Thread the lead wires into the stem (s)(F) and connector (V) then secure the stem(s) (F) onto fixture
body (T).
9. Secure the canopy (S), face plate (A), star washer (R) and grounding wire (if applicable) by butterfly
nut (Q).
10. Identify color coding of fixture wires.
11. Connect the black wire from the fixture with the black wire (live wire) from the outlet box (J) by
wire connector (G), and wrap the wire connector (G) with electrical tape for a more secure
connection.
12. Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box (J)
by wire connector (G), and wrap the wire connector (G) with electrical tape for a more secure
connection.
13. Partially thread green grounding screw (H) into side hole (I) on mounting plate (C) (see fig.1).
14. Wrap the bare grounding wire from the fixture canopy around the green grounding screw stem
(H) on the mounting bar leaving enough excess wire. Connect the greenish grounding wires from
hanging cord and excess grounding wire from the fixture canopy with the grounding wire from
outlet box (J) by using a wire connector (G), then wrap the wire connector (G) with electrical tape
for a more secure connection.
15. Tuck wires inside outlet box (J).
FIXTURE ASSEMBLY INSTRUCTIONS
Warning: This fixture is for indoor use only.
1. Place glass shade(s) (L) into holder(s) (M).
2. Place retaining rings (N) over lamp sockets and thread into place. Secure retaining ring(s) (N) with
tool (U).
3. Install lamp(s). Do not exceed recommended wattage.
4. Turn power back on at circuit box.
FIGURE 2.
FIXTURE
WIRES:
Black
*OUTLET BOX (J)
WIRE CONNECTORS (G)
MOUNTING PLATE (C)
WARNING
*GREEN GROUNDING
SCREW (H) Turn off electricity to the mounting site before beginning installation.
STAR WASHER (R)
Mounting instructions must be followed exactly as shown for the fixture to be safely
supported.
CONNECTOR (V)
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
clean this fixture.
NOTE FOR FIXTURES THAT ARE SOLID BRASS:
Your hand-crafted, solid brass lighting fixture has been coated with a durable, baked-on acrylic
lacquer which gives maximum protection against the weather. However, in time the brightness of
the brass will tarnish, giving way to an authentic old-world brass finish. To keep your solid brass
fixture looking new for years to come, regularly apply a good quality, non-abrasive car wax to all
metal surfaces, giving the fixture an extra protective covering.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
HOLDER (M)
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
GLASS
SHADE (L)
RETAINING
RING (N)
TOOL (U)
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.
*NOT SUPPLIED
Used under license by Westinghouse Lighting.
FIXTURE FIXTURE
WIRES: WIRES:
White
Bare
Copper
(Ground)
HOUSE HOUSE
HOUSE
WIRES: WIRES:
WIRES:
Black White
Bare
(Hot) (Neutral)
Copper
(Ground)
www.westinghouselighting.com
All rights reserved.
Guide d'utilisation
Appareil d' é clairage pour utilisation intérieure
GARANTIE LIMITÉE DE CINQ ANS
Ce luminaire Westinghouse est garanti pièces et main-d'oeuvre pour une période de Cinq ans à compter
de la date d'achat. Cette garantie remplace toute autre garantie, explicite ou implicite.
Cette garantie ne couvre pas les phénomènes naturels comme les dommages de la foudre, ni la corro-
sion ou la décoloration des composants, pas plus qu'elle ne couvre les dommages causés par les abus,
une installation inappropriée, les surtensions électriques ou les actes de tiers.
Cette garantie ne couvre pas les coûts de dépose et de pose du luminaire.
En cas de défaillance du produit, pour une raison quelconque, couverte par cette garantie, veuillez
nous contacter via www.westinghouselighting.com/contact-us.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION INTÉRIEURE
Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d'éclairage a été
conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à
nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA: Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces
y sont avant de mettre l'emballage au rebut (voir fig. 1).
MISE EN GARDE: L'ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l'installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de
commencer l'installation. Un câblage approprié est essentiel au bon fonctionnement de cet
appareil d'éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur
ou un plafond, n'endommagez pas les câbles électriques, les canalisations de gaz ou d'eau. Si
l'un des composants de raccordement ou de l'appareil d'éclairage est endommagé, n'installez
pas cet appareil d'éclairage. Retournez-le à l'endroit où vous l'avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l'appareil
d'éclairage est doté d'un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se
trouvent sur l'étiquette U.L. et sur l'emballage de l'appareil d'éclairage.)
FIGURE 1.
ANCRAGES DE
CLOISON SÈCHE (E)
TROU LATERAL (I)
TROUS EXTERIEURS (O)
*VIS DE LA BOITE DE
SORTIE DE COURANT (P)
VIS (K)
ÉCROU PAPILLON (Q)
PLAQUE AVANT (A)
CHAPEAU (S)
TIGE (F)
LE CORPS DE
L'APPAREIL
D'ECLAIRAGE (T)
Il est possible que le dessin illustré ici ne
soit pas la reproduction exacte de l'appareil
d'éclairage contenu dans la boîte.
Les instructions d'installation demeurent
cependant valables.
Made in China
Instructions d'installation
*BOITE DE SORTIE
*FIL DE MISE
DE COURANT (J)
A LA TERRE
CONNECTEURS DE FIL (G)
PLAQUE DE
FIXATION (C)
*VIS DE MISE A LA
TERRE (VERTE) (H)
RONDELLE ÉTOILE (R)
CONNECTEUR (V)
ECROUS
CAPUCHONS (B)
SUPPORT (M)
ABAT-JOUR
EN VERRE (L)
LA BAGUE DE
RETENTION (N)
OUTIL (U)
*NON FOURNI