Publicidad
Idiomas disponibles
Idiomas disponibles
Once the Tactical Fire Light has been installed into the Multi-Angle
Helmet Mount, the entire unit is ready to be attached to the Fire Helmet
or Hard Hat. The Multi-Angle Mount comes with two 5/16" - 18 x 1/4" Brim
Mounting Allen Set Screws pre-installed. These two Allen Set Screws are
designed to be used with the thicker brim found on most Fire Helmets.
(Image 7) It may be necessary to switch these two Allen Set Screws with
the 5/16" - 18 x 3/8" set if the thickness of the brim of the helmet or Hard Hat
makes it impossible to use the shorter set. (Image 8)
Position the Multi-Angle Mount over the edge of the brim and tighten
the appropriate set of Allen Set Screws using the included 5/32" Allen
Wrench. (Image 9)
CAUTION: Be careful when tightening the Allen Set Screws. Do not
over-tighten. Doing so may damage or crush the brim of the Fire
Helmet or Hard Hat. These two Allen Set Screws should only be
tightened enough to prevent the mount from coming loose from the
helmet. Over time these screws may come loose. Periodically check
and re-tighten as needed.
SUGGESTION:
Application of a thread locking solution (such as
Loctite® Threadlocker Blue) may be applied to secure these Allen Set
Screws. Do not use the "red" version of this product as it is designed for
a more permanent installation and would make it diffi cult to remove these
Allen Set Screws in the future.
SETTING THE ANGLE OF THE MULTI-ANGLE MOUNT
Image 10
Once mounted to the helmet, the user can change the angle of the
mount through 140 degrees of adjustment in order to position the light
appropriately for the optimum clearance and illumination. (Image 10)
To adjust the angle, simply loosen the Angle Lock Socket Head Cap
Screw using the included 5/32" Allen Wrench. (Image 11)
Select the angle and then tighten the Angle Lock Socket Head Cap
Screw securely. (Image 12)
Test to make sure that the angle will not change and continue tightening
as needed.
OPERATION
The Tactical Fire Light has two light modes: MOMENTARY and
CONSTANT-ON. The light has a single tail switch providing access to all
modes.
MOMENTARY
Lightly press the tail-cap switch for momentary operation. Release the
switch to turn the light off.
CONSTANT-ON
Press the tail-cap switch until it clicks and then release for constant-on
mode. Press and release the switch again to turn the light off.
BAYCO PRODUCTS LIMITED LIFETIME WARRANTY
WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in
workmanship and materials for the original purchaser's lifetime. The Limited
Lifetime Warranty includes the LEDs, housing and lenses. Rechargeable
batteries, chargers, switches, electronics and included accessories are
warranted for a period of two years with proof of purchase. Disposable, non-
rechargeable batteries are excluded from this warranty. Normal wear and
failures which are caused by accidents, misuse, abuse, faulty installation
and lightning damage are also excluded.
In the event that Bayco Products, Inc. receives notice that any product
does not conform to its warranty, the original purchaser's sole and exclusive
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mynightstick.com
Image 11
Image 12
remedy, and Bayco Products, Inc.'s sole and exclusive liability, shall be
for Bayco Products, Inc., at its sole option, to either repair or replace the
non-conforming product in accordance with this limited warranty. The
original purchaser shall follow the instructions below to qualify for a repair
or replacement product. This is the only warranty, expressed or implied,
including any warranty of merchantability or fi tness for a particular purpose.
IN NO EVENT WILL BAYCO PRODUCTS, INC. OR ITS AFFILIATES
OR SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY KIND REGARDLESS OF
THE FORM OF ACTION, WHETHER IN CONTRACT, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE.
CUMULATIVE LIABILITY TO CUSTOMER, FROM ALL CAUSES OF
ACTION AND ALL THEORIES OF LIABILITY, WILL BE LIMITED TO AND
WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT PAID
BY CUSTOMER.
If this product is used for rental purposes, the warranty term is reduced
to 90 days from the date of purchase.
WARRANTY CLAIMS – USA
Return the product to the place of purchase for all warranty related
issues. If this is not possible, contact Bayco Customer Service at (800) 233-
2155 M-F 8-5 Central Time for a Return Goods Authorization (RGA). Do not
return this product to Bayco without fi rst receiving an RGA Number from
Bayco Customer Service. When returning the product, the RGA Number
must be written on the outside of the shipping box.
WARRANTY CLAIMS – OUTSIDE OF USA
Return the product to the place where purchased for all warranty related
issues.
EXTENT OF COVERED WARRANTY WORK
Bayco will repair or replace this product at our option. If it is determined
that the warranty is no longer in effect, Bayco will contact you with a repair
estimate before beginning any work.
WARRANTY QUESTIONS
If you have any questions about this warranty or any other Bayco
product inquiries, please contact Bayco Customer Service at (800) 233-
2155 M-F 8-5 Central Time.
RECORD YOUR WARRANTY INFORMATION
Please record your FDL-300R-K01 product information here for use with
any warranty claim.
Date of Purchase ________________________________
MODE D'EMPLOI
MERCI D'AVOIR CHOISI LA LAMPE DE POCHE FDL-300R-K01 À
VOYANT LUMINEUX TACTIQUE ET DISPOSITIF POUR CASQUE À
VEUILLEZ CONSERVER CE MODE D'EMPLOI
Veuillez lire ces instructions avant d'utiliser votre lampe de poche FDL-
300R-K01 à voyant lumineux tactique et dispositif pour casque à angles
multiples. Elles contiennent des informations importantes sur l'utilisation et
l'assemblage.
CONTENU DE LA BOÎTE
1– Lampe de poche à voyant lumineux tactique FDL-300R
1 – NS-HMC1 Dispositif pour casque à angle multiples
1 – Piles au lithium CR-123
1 – Ensemble de vis à têtes creuses pour dispositif de lampe de poche
(déjà monté) de 5/16 '' – 18 x ¼ ''
1 – Ensemble de vis à têtes creuses pour dispositif de rebord (déjà
monté) de 5/16 '' – 18 x ¼ '' – pour casques d'incendie
INS-FDL-300R-K01-15
FDL-300R-K01
ANGLES MULTIPLES!
THE TOTAL
Publicidad
