air&me SOLNAN Manual De Usuario página 9

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 15
MAIN FUNCTIONS
[POWER] FUNCTION: Solnan is equipped with 3 levels of diffusion power, allowing to increase
C
the speed of air humidification and to regulate the intensity of the mist. The corresponding
number appears on the digital display:
1 – Low power
2 – Medium power
3 – High power
When the digital display indicates the ambient humidity rate, press it once to increase the
preset power. Press it a second time to change the power.
At full power, the mist produced may condense around the appliance and give the impres-
sion of a tank leak. To avoid this phenomenon, reduce the diffusion power and/or place the
humidifier towards a heat source (at about 1 meter).
[TIMER] FUNCTION: This function allows you to choose the operating time of your appliance,
B
from 1 to 12 hours.
1. By pressing button
, the digital display indicates "01" for "1 hour of operation". Press the
B
button repeatedly to reach the desired value.
2. Without any action on your side, the digital timer display stops flashing after 5 seconds,
which means that the setting is successful.
3. Once the desired operating time is set up, the digital display indicates the remaining time
every minute, and decreases from hour to hour. If you have set the Timer to "03" (3 hours),
the digital display will indicate "02" after one hour of operation.
To cancel the Timer setting, hold down button
[HYGROSTAT] FUNCTION: This function allows you to set up the ambient humidity rate to the
D
value you want (between 30 and 90%). For maximum comfort, we recommend a humidity
rate between 45 and 55%.
1. Before pressing button
, the digital display indicates the ambient humidity rate.
D
2. Press button
, several times to select the value you want. The value increases in steps
D
of 5%.
3. Without any action on your side, the digital hygrostat display stops flashing after 5 se-
conds, which means that the setting is successful.
4. Once the desired humidity rate is set up, the digital display indicates this rate every mi-
nute, flashing slowly.
Set up of the appliance in CONTINUOUS mode:
To activate this function, press several times the button
After 5 seconds, the digital display indicates again the ambient humidity rate.
Caution: By selecting the [HYGROSTAT] function, it is not possible to adjust the power of the
appliance.
16
for 2 seconds.
B
until the "CO" acronym appears.
D
NIGHT MODE: You can activate or deactivate the LED display of the appliance:
1. Hold down the button
for 2 seconds: the blue LED situated under the appliance and the
D
digital display turn off.
2. Press one of the buttons to reactivate the digital display.
3. Press again one of the buttons to modify the operating mode of the appliance.
4. Hold down the button
again to reactivate the LED lights.
D
AUTOMATIC AIR HUMIDIFICATION
Solnan is equipped with an [HYGROSTAT] function that allows you to choose a desired humidity
rate in your room. By making this setting, the appliance will automate its operating.
Desired humidity rate according
to the ambient humidity rate
Higher than 16% or more
Higher than 10 to 15%
Higher than 1 to 9%
Lower
MAINTENANCE
• Make sure the unit is turned off and unplugged before handling.
• Do not immerse the device in water or any other liquid.
• Do not use corrosive, abrasive or flammable products to clean the unit.
CLEANING THE TANK: To avoid scale deposits, clean the tank at least once a month with a
suitable product or white vinegar. To do this, remove the tank from the unit and remove the
cap, then fill it with water and cleaning agent. Let stand for 15 minutes, then empty and rinse
the tank thoroughly with clean water before putting it back in place and turning on the device
again.
CLEANING ULTRASONIC PLATE : Dry the ultrasonic plate and clean it with a soft brush. Then wipe
it with a soft cloth.
STOCKAGE: To avoid any bacteria or virus proliferation, never store the appliance with water
inside the tank and be sure that the appliance is perfectly dry.
1. Empty and clean the tank.
2. Clean the pre-filter.
3. Store the product in a place that is protected against dust and that is clean and dry.
Automatic humidification power
3 – High power
2 – Medium power
1 – Low power
The appliance is in standby
17

Publicidad

Tabla de contenido
loading

Productos relacionados para air&me SOLNAN

Tabla de contenido