Replacement Parts; Safety Notes - Modellsport MULTIPLEX EasyCub 33 2637 Instrucciones

!
These operating instructions are an integral part of the
product. They contain important information and safety
notes, and should be kept in a safe place at all times. Be
sure to pass them on to the new owner if you ever dispose
of the product.
1. I
NTRODUCTION
The "EASYCUB" brushless power set # 33 2637, is suit-
able for any beginner's model or trainer with an all-up
weight of up to about 1000 g, and contains all the compo-
nents required to power your model. There is no soldering
to do - we have done it all for you. All you have to do is to
install the components of the power set with the help of
these instructions, and you can go flying.
2. C / R
ONTENTS EPLACEMENT PARTS
• 1 Himax C 2816-1220 motor
• 1 MULTIcont BL-27/II speed controller
• 1 10" x 5" propeller
• 1 propeller driver and spinner for motor shafts ∅ 4 mm,
prop-shaft 6 mm
• Various small items for installation in the model
3. T
. O
YP PERATIONAL
"EASYCUB"
2S LiPo / 10" x 5" prop
Recommended Battery:
MULTIPLEX Li-BATT eco 2/2000
MULTIPLEX Li-BATT eco 2/3000
MULTIPLEX Li-BATT BX 2/2100
MULTIPLEX Li-BATT BX 2/2500
MULTIPLEX Li-BATT BX 2/3200
If you use the Himax C 2816-1220 motor and the stan-
dard propeller supplied in the set, do not use more than a
2S LiPo pack or 6 NiXX cells
4. S N
AFETY OTES
The power set "EASYCUB" is designed exclusively for
use in modelling applications. Incorrect use can result in
serious personal injury.
• Read the instructions before initiation
• Before every flight, check that the motor and propeller
are securely mounted
• Remove all movable objects from the area around the
propeller before switching the motor on
• Do not allow clothing or any of your extremities to get
close to the spinning propeller
• Never start running the motor in your hand
• Stop the motor immediately if you notice vibration.
Eliminate the cause of the vibration before running it
again; you may need to correct the balance of the pro-
peller
• Make sure the power system is adequately cooled; do
not allow anything to obstruct the free circulation of air
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions for Power Set „EASYCUB"
# 33 3017
# 7 2275
# 73 3106
# 33 2314
D P S
ATA OF OWER
Current drain: approx.17.0 A
# 15 7230
# 15 7235
# 15 7130
# 15 7190
# 15 7135
.
5. A
SSEMBLING OF THE
"EASYCUB"
Propeller
Collet
Spinner
1. Screw the motor to the motor mount
motor is free to rotate. When deploying the motor
cables, check that they cannot make contact with the
spinning motor. Secure the motor leads with Velcro
tape or similar.
2. Fit the propeller driver and clamping ring on the motor
ET
shaft.
3. Look at the propeller from the front (the face stating the
propeller size), and check whether the hole is bored
centrally, i.e. whether it lines up correctly with the
moulded-in guide hole on the underside. If this is not
the case, adjust the propeller bore so that the front hole
lines up with the rear one. CAUTION: don't adjust or
drill out the rear guide hole.
4. Locate the retainer ring supplied in the set, and place it
in the rear guide hole. Fit the propeller on the driver,
and secure it with the spinner.
6. I
NITIATION OF THE
" EASYCUB "
1. Connect the three wires attached to the speed control-
ler to the three wires attached to the motor; the order of
connection is unimportant.
2. Locate the UNI connector attached to the speed con-
troller, and connect it to your receiver.
3. Switch the transmitter on, and check that the throttle
control is at the "OFF" position.
4. Connect the flight battery to the speed controller.
5. Check the direction of rotation of the motor: it should
spin clockwise when viewed from the tail, looking for-
ward. If this is not the case, disconnect the flight battery
and swap over any two of the three motor wires.
6. Switch off the motor brake at the speed controller; the
method of doing this is described in the instructions
supplied with the controller.
P S
OWER ET
Motor mount
Propeller driver
ensure that the
P S
OWER ET
Page 1/2