Useful Information - Atlas Copco P2540 Instrucciones De Operación Y Seguridad

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 19
P2540
2006/42/EC
Harmonised standards applied:
ISO 11148-4
Technical file available from:
Quality Manager, Atlas Copco Industrial Technique,
Stockholm, Sweden
Stockholm, 1 July 2013
Tobias Hahn, Managing Director
Signature of issuer
Installation
Air quality
• For optimum performance and maximum machine
life we recommend the use of compressed air with
a maximum dew point of +10°C. We also recom-
mend the installation of an Atlas Copco refrigera-
tion-type air dryer.
• Use a separate air filter of type Atlas Copco FIL.
This filter removes solid particles larger than 15
microns and also removes more than 90 % of li-
quid water. The filter must be installed as close
as possible to the machine/equipment and prior
to any other air preparation unit such as REG or
DIM (please see Air Line Accessories in our main
catalogue). Blow out the hose before connecting.
Models which need air lubrication:
• The compressed air must contain a small quantity
of oil.
We strongly recommend that you install an Atlas
Copco oil-fog lubricator (DIM). This should be
set according to air consumption by the air line
tool according to the following formula:
L = Air consumption (litre/s).
(May be found in our sales literature).
D = Number of drops per min (1 drop = 15 mm
L* 0.2 = D
this applies to the use of long work cycle air line
tools. A single point lubricator type Atlas Copco
Dosol can also be used for tools with short running
cycles.
Information about Dosol settings may be found
under Air Line Accessories in our main catalogue.
Lubrication-free models:
• In the case of lubrication-free tools it is up to the
customer to decide on the peripheral equipment
to be used. However, it is no disadvantage if the
compressed air contains a small quantity of oil
EN
3
)
© Atlas Copco Industrial Technique AB - 9836 5862 00
Safety and operating instructions
e.g. supplied from a fog lubricator (DIM) or Dosol
system. This does not apply to turbine tools, which
should be kept oil free.
Compressed air connection
• The machine is designed for a working pressure
of 6–7 bar = 600–700 kPa = 87–102 psi.
• Blow out the hose before connecting.
Maintenance
Rust protection and internal cleaning
Water in the compressed air, dust and wear particles
cause rust and sticking of piston, valves etc. This can
be solved by flushing with oil (some drops), running
the machine for 5-10 seconds and absorbing the oil
in a cloth. Make this preparation before longer
standstills.
Overhaul and lubrication
If the machine is normally used as a heavy-duty
machine it should be dismantled, overhauled and
cleaned after 4 months in operation. If the machine
is not running properly, it should be taken out of
service for inspection.
At the overhaul the disassembled parts should be
checked according to the spare parts list. Sliding
parts should be lubricated with oil prior to assembly.
Use lubricants of good quality. The air motor oils
and greases mentioned in the chart are examples of
lubricants which are recommended.
Grease guide
Brand
Grease
BP
Energrease LS-EP2
Esso
Beacon EP2
Q8
Rembrandt EP2
Mobil
Mobilegrease XHP 222
Shell
Alvania EP2
Texaco
Multifak EP2
Molycote
BR2 Plus

Useful information

C Log in to Atlas Copco www.atlascopco.com
You can find information concerning our products,
accessories, spare parts and published matters on our
website.
Ergonomic guidelines
Consider your workstation as you read through this
list of general ergonomic guidelines and see if you
Air lubrication
Energol E46
Arox EP46
Chopin 46
Almo Oil 525
Torcula 32
Aries 32
5

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

8425 0103 40

Tabla de contenido