Lasko 3138 Instrucciones página 4

COLUMN AND MOTOR ASSEMBLY
Locate Motor Hardware Bag to Assemble Column and Motor Assembly.
1. Place flat section on Upper Tube of Column Assembly next to
Neck on Motor Assembly. Align the 1/2" diameter hole in the
flat section on the Upper Tube of Column Assembly with the
1/2" diameter hole in the Motor Assembly. (Figure 4)
2. Insert the 1/2" X 1" Hex Bolt (3/4" head) through the Motor
Neck, and the Upper Tube Assembly. Place 1/2" diameter Split
Lockwasher then the 1/2" diameter Hex Nut (3/4" head) and
tighten fully with a adjustable wrench. (Figure 4)
3. From the same side of the Motor Neck,insert one 1/4-20 X 1 5/8"
Carriage Bolt through the Arc-Shaped Slot in the Motor Neck
and Hole in the Upper Pipe of Column Assembly. (Figure 4)
To Fasten: Place one 1/4" Flatwasher, one 1/4" Internal Tooth Lock-
washer, a second 1/4" Flatwasher and then tighten the Adjustable
Knob over the remaining threads.
4. Attach pull string to motor speed switch, if desired.
Actual motor not shown for
detailed hardware view.
COLUMN/MOTOR TO BASE ASSEMBLY
1. Rest Column and Motor Assembly on floor next to the Base
Assembly. Tilt Base Assembly up on end. Pick up lower pipe
of Column Assembly and insert into the Mounting Flange. (Figure 5)
2. Tighten the 3/8-16 X 1" Square Head Bolt into the
Mounting Flange.
3. Tilt entire assembly to the upright position.
MAKE SURE BOLTS IN COLUMN AND MOTOR ASSEMBLY STEPS
ARE TIGHT BEFORE STANDING FAN UPRIGHT.
4. Loosen 3/8-16 X 1" Square Heat Bolt in the Mounting Flange.
This will allow the Column to settle in the bottom of the Base
after setting the Fan upright.
5. Tighten the 3/8-16 X 1" Square Head Bolt in the Mounting
Flange.
Rev. E 8/10
Figure 4
Figure 5
4
GRILL AND BLADE ASSEMBLY
Locate remaining parts from Motor Hardware Bag to Assemble
Grills and Blade to the Motor.
1. Install the Rear Grill onto the Motor, lining up the six holes in the
grill with the six threaded holes in the motor mounting flange.
Install (6) 10-32 X 5/16" Hex Screws through the rear grill into
the mounting flange. Securely tighten all (6) screws. (Figure 6)
2. Push the Fan Blade onto the Motor Shaft, centering the Hub
facing away from the motor, until it stops against the shaft
(Inset A) . Align Square Head Bolt with flat of the motor shaft.
TIGHTEN VERY SECURELY WITH AN ADJUSTABLE WRENCH.
Failure to securely tighten the Bolt could result in damage to
the Fan and/or personal injury.
3. Hold the Front Grill so that the name, in the center, is right side
up and straight across. Starting at the top: Fasten Front Grill
to Rear Grill by sliding the hooked wires on the Front Grill over
the outermost ring on the Rear Grill. (Figure 7 / Detail A). The
bottom most hooks will require the use of a flathead screwdriver
to complete assembly. Stand behind the Fan. Slip the flat of
the screwdriver between the Front and Rear Grills, next to one
of the unfastened hooks. (Figure 7 / Detail B) Pull screwdriver
handle upwards towards the Rear Grill. Slip the Front Grill hook
over the Rear Grill outer ring with a push. Repeat procedure
with remaining hooks.
CAUTION: DO NOT BEND WIRES ON THE FRONT OR THE
REAR GRILLS.
Figure 7
Inset A
Figure 6
Detail A
Detail B
5084445